Abstract:One of the main challenges for the treatment of oily wastewater is emulsion separation. However, emulsions are generally more stable and difficult to separate. Herein, we report a facile strategy for the fabrication of monolithic oil/water separation materials by modifying melamine sponge with magnesium hydroxide (MH) coating, which can effectively separate immiscible oil/water mixtures and surfactant-stabilized emulsions. Its demulsification efficiency for the surfactant-stabilized emulsions can exceed 99.7%. In particular, the separation flux in a continuous emulsion separation system driven by a low-power pump can reach as high as 6.7 × 104 L m–2 h–1. MH particles coated on the surface of the sponge is one of the key factors for the formation of superhydrophobic surfaces and provide abundant adsorption sites for oil. Moreover, it was found that the surfactant added during the MH synthesis process not only affects the surface charge of MH but also interacts with the surfactant in the emulsion, which can promote instability and breaking of the oil/water interfacial film of emulsion.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.iecr.0c01276?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.iecr.0c01276</a>.Physical properties of the as-prepared samples (Table S1); schematic diagram of S-MH preparation (Figure S1); XRD patterns of as-prepared S-MH (Figure S2); FT-IR spectra of MH, SDBS, and S-MH (Figure S3); N2 adsorption–desorption isotherms and pore size distribution of S-MH (Figure S4); TEM images of (a) S-MH, (b) C-MH, and (c) MH (Figure S5); Effect of S-MH suspension concentration on water contact angle and sliding angle of S-MH/MS. (Figure S6); Effect of S-MH content in solution during synthesis on water contact angle of S-MH/MS S-MH/MS (Figure S7); separation of nonturbulent oil/water mixture and separation of turbulent oil/water mixture (Figure S8); photographs showing the preparation of emulsion (Figure S9); photographs showing the oil/water separation device (Figure S10); photographs showing the stability of surfactant-free emulsion (SF-E), CTAB-stabilized emulsion (CS-E) and SDS-stabilized emulsion (SS-E) (Figure S11); optical micrograph of surfactant-free emulsion (SF-E) and SDS-stabilized emulsion (SS-E) and histogram of the oil droplet size distribution in case of SF-E and SS-E (Figure S12); micrograph of the filtrate obtained by S-MH/MS separating SS-E and the particle distribution (Figure S13) (<a class="ext-link" href="/doi/suppl/10.1021/acs.iecr.0c01276/suppl_file/ie0c01276_si_001.pdf">PDF</a>)Process of S-MH/MS separating emulsion (CS-E) driven by gravity (<a class="ext-link" href="/doi/suppl/10.1021/acs.iecr.0c01276/suppl_file/ie0c01276_si_002.mp4">MP4</a>)Process of S-MH/MS separating emulsion driven by peristaltic pump (<a class="ext-link" href="/doi/suppl/10.1021/acs.iecr.0c01276/suppl_file/ie0c01276_si_003.mp4">MP4</a>)This article has not yet been cited by other publications.

Universal Rapid Demulsification by Vacuum Suction Using Superamphiphilic and Underliquid Superamphiphobic Polyurethane/Diatomite Composites

Coalescence and separation of surfactant-stabilized water-in-oil emulsion via membrane coalescer functionalized by demulsifier

Efficient demulsification of cationic polyacrylate for oil-in-water emulsion: Synergistic effect of adsorption bridging and interfacial film breaking

Contactless Interfacial Thin‐Film Breaking Caused Splash‐Like Demulsification of Floating Micron Emulsions via Ionic Wind

Demulsification of water-in-heavy oil emulsions by oxygen-enriched non-ionic demulsifier: Synthesis, characterization and mechanisms

Superhydrophobic polyurethane sponge for efficient water-oil emulsion separation and rapid solar-assisted highly viscous crude oil adsorption and recovery

Enhanced demulsification of alkaline-surfactant-polymer flooding O/W emulsion by multibranched polyether-polyquaternium based on the size effect of oil droplets

Ultrafast and Continuous Separation of Water-in-Oil Emulsions Via Constructing a Dual-Layered Superwetting Membrane

High‐Flux Steady‐State Demulsification of Oil‐In‐Water Emulsions by Superhydrophilic‐Oleophobic Copper Foams with Ultra‐Small Pores Under Pressure

Simple Amphoteric Charge Strategy to Reinforce Superhydrophilic Polyvinylidene Fluoride Membrane for Highly Efficient Separation of Various Surfactant-Stabilized Oil-in-Water Emulsions

3D Superhydrophobic Sponge Coated with Magnesium Hydroxide for Effective Oil/Water Mixture and Emulsion Separation

Multifunctional superwetting positively charged foams for continuous oil/water emulsion separation and removal of hazardous pollutants from water

Removal of Oil from a Crude Oil-in-Water Emulsion by a Magnetically Recyclable Diatomite Demulsifier

Highly efficient oil-water separation and oil adsorption with hydrophobic hydrotalcite/polyurethane porous composite foam

Fabrication of hyperbranched polyether demulsifier modified PVDF membrane for demulsification and separation of oil-in-water emulsion

Demulsifier-Inspired Superhydrophilic/Underwater Superoleophobic Membrane Modified with Polyoxypropylene Polyoxyethylene Block Polymer for Enhanced Oil/Water Separation Properties

Advancing oil-water separation: Design and efficiency of amphiphilic hyperbranched demulsifiers

De-emulsification performance and mechanism of polyether-polyquaternium copolymers and compounding products on tight gas produced water

Methacrylated Hyperbranched Polyglycerol As a High-Efficiency Demulsifier for Oil-in-Water Emulsions

Photothermal, Magnetic, and Superhydrophobic PU Sponge Decorated with a Fe3O4/MXene/Lignin Composite for Efficient Oil/Water Separation

Rapid demulsification and phase separation in a miniaturized centrifugal demulsification device