Abstract:PurposeThe purpose of this paper is to present recent work designing a mechanical robotic hand for self‐adaptive grasping, human‐like appearance, which can be used in a humanoid robot. Conventional robotic devices are relatively complex, large, cumbersome and difficult to be installed in a humanoid robot arm. Under‐actuated robot hands use less motors to drive more rotating joints, thus to simplify the mechanical structure, decrease the volume and weight and finally lower the difficulty of control and the cost.Design/methodology/approachA novel under‐actuated finger mechanism is designed, which is based on a gear‐rack mechanism, spring constraint and an active sleeve middle phalanx. The principle analyses of its self‐adaptive grasp and end power grasping are given. A new multi‐fingered hand named as TH‐3R Hand is designed based on the finger.FindingsThe design finger mechanism can be used in a robotic hand to make the hand obtain more degrees of freedom (DOF) with fewer actuators, and good grasping function of shape adaptation, decrease the requirement of control system. TH‐3R Hand has five fingers, 15 DOF. All fingers are similar. TH‐3R Hand has many advantages: it is simple in structure, light in weight, easy to control and low in cost. TH‐3R Hand can passively adapt different shapes and sizes of the grasped object. Experimental studies have demonstrated the self‐adaptation in grasping of the finger.Research limitations/implicationsThe implication of this research is that under‐actuated robotic hands are appropriate for the missions of grasping different objects. The limitation of the research to date is that issues of sensors, control, and communication have not yet been addressed.Practical implicationsKey technologies of the under‐actuated finger and TH‐3R Hand, with self‐adaptive grasping, human‐like appearance and low‐cost lightweight, are feasible. These technologies have the potential to make a significant impact.Originality/valueThese results present a self‐adaptive under‐actuated grasp concept and a humanoid robotic hand with under‐actuated gear‐rack mechanism.

Pneumatic-Electric Hybrid Drive Robot Hand for Both Powerful Grasping and Dexterous Manipulation Using Passive Clutch Mechanism

Design of a Lightweight Single-Actuator Multi-Grasp Prosthetic Hand With Force Magnification

Research of Passive Grasp Multi-fingered Robot Hand

Under-actuated Passive Adaptive Grasp Humanoid Robot Hand with Control of Grasping Force

Design Principle of a Dual-Actuated Robotic Hand With Anthropomorphic Self-Adaptive Grasping and Dexterous Manipulation Abilities

Development of a Novel Impedance-Controlled Quasi-Direct-Drive Robotic Hand

A Compliant, Underactuated Hand for Robust Manipulation

Electromyographic prosthetic hand using grasping-force-magnification mechanism with five independently driven fingers

Development of a Novel Impedance-Controlled Quasi-Direct-Drive Robot Hand

Hybrid Gripper with Passive Pneumatic Soft Joints for Grasping Deformable Thin Objects

A Soft-Rigid Hybrid Gripper With Lateral Compliance and Dexterous In-Hand Manipulation

Five-fingered Hand with Wide Range of Thumb Using Combination of Machined Springs and Variable Stiffness Joints

Novel differential mechanism enabling two DOF from a single actuator: Application to a prosthetic hand

Multi-Mode Compound Grasping Robot Finger Driven by Linkage

Design of the Human-like Dexterous Hand Actuated by Pneumatic Muscle Actuators

A Parallel And Active Hybrid Grasping Robot Finger With A Single Chain Transmission Mechanism

Sensor-Less and Control-Less Underactuated Grippers With Pull-In Mechanisms for Grasping Various Objects

Development and Control of a Pneumatic Robot Arm for Industrial Fields

Super Under-Actuated Multi-Fingered Mechanical Hand with Modular Self-Adaptive Gear-Rack Mechanism

Pisa-Gbm Hand: an Indirectly Self-Adaptive Robot Hand with Built-In Actuators

Bioinspired Multimodal Multipose Hybrid Fingers for Wide-Range Force, Compliant, and Stable Grasping