The Aerospace Corporation’s Compendium of Recent Single Event Effect Results

J. George,A. Wright,R. Koga,D. Mabry,A. Yarbrough,C. A. Langford,S. Davis

DOI: https://doi.org/10.1109/REDW.2019.8906629

2019-07-01

Abstract:Single Event Effect testing using heavy ions and protons was performed on several commercial components to determine the response of these components to the space radiation environment.

Physics,Engineering

What problem does this paper attempt to address?

Radiation-Induced Single-Event Effects on the Van Allen Probes Spacecraft

Richard H. Maurer,Kristin Fretz,Matthew P. Angert,David L. Bort,John O. Goldsten,Geffrey Ottman,Jeff S. Dolan,Gerald Needell,David Bodet

DOI: https://doi.org/10.1109/tns.2017.2754878

IF: 1.703

2017-11-01

IEEE Transactions on Nuclear Science

Abstract:Electronic devices on the Van Allen Probes mission have experienced more than a thousand single-event effects (SEE) during the 4.5 years of transit through the inner and outer earth trapped radiation belts. The majority of these SEE have been due to trapped protons determined by the orbit timing and the dose rate response of the engineering radiation monitor. Fault tolerant systems engineering and spacecraft operation have enabled a successful mission to date without a safe mode or spacecraft emergency.

engineering, electrical & electronic,nuclear science & technology
Irradiation Tests for Commercial Off-the Shelf Components with Atmospheric-like Neutrons and Heavy-Ions

Paolo Branchini,Andrea Fabbri,Sacha Cormenier,Marco Bernardini,Giovanni Romanelli,Enrico Preziosi,Roberto Senesi,Carla Andreani,C. Frost,Carlo Cazzaniga,Toni Fabio Catalano,Mario Buffardo

2023-11-29

Abstract:This paper presents the results of the irradiation, performed with atmospheric-like neutrons and heavy-ions, of Commercial Off-the Shelf Components (COTS), which can be used in space missions. In such cases, it is crucial to perform tests in a radiation environment that emulates the environment of different orbits around Earth. In our study we used atmosphericlike neutrons with fluences up to 1011 neutrons/cm-2 and Kr ions of fluences up to 107 ions/cm-2. These intensities are augmented with respect to the atmospheric one in order to shorten the irradiation time while simulating a long-time exposure during a possible mission in Low Earth Orbit (LEO). A similar radiation environment to LEO can also be present during High-Energy Physics experiments. Therefore, the study herby reported can also be helpful for accelerator physics. In this paper we show in detail procedures, setup and results we have obtained on a commercial device normally exploited in automotive environments.

Systems and Control
Modeling the effects of low-LET cosmic rays on electronic components

A. Keating,P. Goncalves,M. Pimenta,P. Brogueira,A. Zadeh,E. Daly

DOI: https://doi.org/10.1007/s00411-012-0412-2

IF: 2.017

2012-05-24

Radiation and Environmental Biophysics

Abstract:The effects of cosmic radiation in single cells, organic tissues and electronics are a major concern for space exploration and manned missions. Standard heavy ions radiation tests employ ion cocktails with energy of the order of 10 MeV per nucleon and with a linear energy transfer ranging from a few MeV cm2 mg−1 to hundreds of MeV cm2 mg−1. In space, cosmic rays show significant fluxes at energies up to the order of GeV per nucleon. The present work aims at investigating single event damage due to low-, high- and very-high-energy ions. The European Space Agency reference single event upset monitor data are used to support the discussion. Finally, the effect of ionization induced directly by primary particles and ionization induced by recoils produced in an electronic device is investigated for different types of devices.

environmental sciences,biology,biophysics,radiology, nuclear medicine & medical imaging
Single Event Effect Testing With Ultrahigh Energy Heavy Ion Beams

A. Gerbershagen,V. Ferlet-Cavrois,R. G. Alía,M. Kastriotou,A. Coronetti,M. Tali,G. Lerner,N. Kerboub,J. Bernhard,C. Cazzaniga,S. Danzeca,P. Fernandez-Martínez,M. Cecchetto,H. Wilkens,V. Wyrwoll

DOI: https://doi.org/10.1109/TNS.2019.2961801

IF: 1.703

2020-01-01

IEEE Transactions on Nuclear Science

Abstract:Single event effect (SEE) testing with ultrahigh energy (UHE) heavy ions, such as the beams provided at CERN, presents advantages related to their long ranges with a constant linear energy transfer value. In the present work, the possibility to test components in parallel is being examined, and results from the CERN 2018 UHE Pb test campaigns are studied. Furthermore, the generation of multibit upsets by the UHE Pb ions is evaluated, and the contribution of possible fragments to the SEE measurements is discussed.

Physics,Engineering
Effects of Electron Beam and Atomic Oxygen Irradiation on Hypervelocity - Impact tested / Polyimide Coated Carbon Fiber-reinforced Plates

Masahiro Nishida,Daichi Kimura,Kyouko Ashida,Naomasa Furuta,Yoshiaki Iwase,Yuichi Ishida

DOI: https://doi.org/10.1016/j.compositesb.2024.111877

IF: 11.322

2024-10-14

Composites Part B Engineering

Abstract:In a low-Earth orbit, space debris orbit at approximately the first cosmic velocity. When space debris strike a spacecraft, ejecta (fragments) from the spacecraft are widely scattered. The reduction in the number of ejecta (fragments caused by impact) must also be considered when selecting spacecraft materials. The authors' group has previously examined the size of ejecta (fragments) and reduction in the number of ejecta. In general, the mechanical properties of polymer materials and CFRP plates may be damaged by space environments, such as radiation (gamma rays and electron beams (EBs)), atomic oxygen (AO), ultraviolet rays, temperature, and thermal cycling. The authors suggested an anti-AO coating/polyimide CFRP as a material resistant to space environments. The effects of EB and AO irradiation on the fracture behavior and ejecta of anti-AO coating/polyimide CFRP were examined for hypervelocity impacts. The results of static three-point flexural tests were compared with the fracture behavior and ejecta. A two-stage light-gas gun was used for the impact tests. Spherical projectiles formed of aluminum alloy 2017-T4 with a diameter of 1.6 mm were used. Photographs of the ejecta scattered in front of each polyimide CFRP plate were captured from the side using a high-speed video camera. The number and weight of the ejecta on the front side and perforation holes were examined.

engineering, multidisciplinary,materials science, composites
Investigation of Single-Event Effects for Space Applications: Instrumentation for In-Depth System Monitoring

André M. P. Mattos,Douglas A. Santos,Lucas M. Luza,Viyas Gupta,Luigi Dilillo

DOI: https://doi.org/10.3390/electronics13101822

IF: 2.9

2024-05-08

Electronics

Abstract:Ionizing radiation induces the degradation of electronic systems. For memory devices, this phenomenon is often observed as the corruption of the stored data and, in some cases, the occurrence of sudden increases in current consumption during the operation. In this work, we propose enhanced experimental instrumentation to perform in-depth Single-Event Effects (SEE) monitoring and analysis of electronic systems. In particular, we focus on the Single-Event Latch-up (SEL) phenomena in memory devices, in which current monitoring and control are required for testing. To expose the features and function of the proposed instrumentation, we present results for a case study of an SRAM memory that has been used on-board PROBA-V ESA satellite. For this study, we performed experimental campaigns in two different irradiation facilities with protons and heavy ions, demonstrating the instrumentation capabilities, such as synchronization, high sampling rate, fast response time, and flexibility. Using this instrumentation, we could report the cross section for the observed SEEs and further investigate their correlation with the observed current behavior. Notably, it allowed us to identify that 95% of Single-Event Functional Interrupts (SEFIs) were triggered during SEL events.

engineering, electrical & electronic,computer science, information systems,physics, applied
Single-event effect testing of the PNI RM3100 magnetometer for space applications

Mark B. Moldwin,Edward Wilcox,Eftyhia Zesta,Todd M. Bonalsky

DOI: https://doi.org/10.5194/gi-11-219-2022

2022-06-23

Abstract:The results of a destructive single-event effect susceptibility radiation test of the PNI RM3100 magnetometer sensor, specifically the MagI 2 C ASIC (application-specific integrated circuit) on the sensor board are presented. The sensor is a low-resource commercial off-the-shelf (COTS) magneto-inductive magnetometer. The device was monitored for destructive events and functional interruptions during exposure to a heavy ion beam at the Lawrence Berkeley National Laboratory's 88 ′′ Cyclotron. The RM3100 did not experience any destructive single-event effects when irradiated to a total fluence of 1.4 × 10 7 cm −2 at an effective linear energy transfer (LET) of 76.7 MeV cm 2 mg −1 while operated at nominal voltage (3.3 V) and elevated temperature (85 ∘ C). When these results are combined with previous total ionizing dose tests showing no failures up to 150 kRad (Si), we conclude that the PNI RM3100 is extremely radiation tolerant and can be used in a variety of space environments.

geosciences, multidisciplinary,meteorology & atmospheric sciences
Mitigating the effects of charged particle strikes on TES arrays for exotic atom X-ray experiments

H. Tatsuno,D.A. Bennett,W.B. Doriese,M. Durkin,J.W. Fowler,J.D. Gard,T. Hashimoto,R. Hayakawa,T. Hayashi,G.C. Hilton,Y. Ichinohe,H. Noda,G.C. O'Neil,S. Okada,C.D. Reintsema,D.R. Schmidt,D.S. Swetz,J.N. Ullom,S. Yamada

DOI: https://doi.org/10.1007/s10909-020-02484-5

2020-05-21

Abstract:Exotic atom experiments place transition-edge-sensor (TES) microcalorimeter arrays in a high-energy charged particle rich environment. When a high-energy charged particle passes through the silicon substrate of a TES array, a large amount of energy is deposited and small pulses are generated across multiple pixels in the TES array due to thermal crosstalk. We have developed analysis techniques to assess and reduce the effects of charged particle events on exotic atom X-ray measurements. Using this technique, the high-energy and low-energy components of the X-ray peaks due to pileup are eliminated, improving the energy resolution from 6.6 eV to 5.7 eV at 6.9 keV.

Instrumentation and Detectors
Biological Effects of Particles with Very High Energy Deposition on Mammalian Cells Utilizing the Brookhaven Tandem Van de Graaff Accelerator

F. Cucinotta,Janapriya Saha,Minli Wang

2013-09-14

Abstract:MATERIALS & METHODS High LET radiation from GCR (Galactic Cosmic Rays) consisting mainly of high charge and energy (HZE) nuclei and secondary protons and neutrons, and secondaries from protons in SPE (Solar Particle Event) pose a major health risk to astronauts due to induction of DNA damage and oxidative stress. Experiments with high energy particles mimicking the space environment for estimation of radiation risk are being performed at NASA Space Radiation Laboratory at BNL. Experiments with low energy particles comparing to high energy particles of similar LET are of interest for investigation of the role of track structure on biological effects. For this purpose, we report results utilizing the Tandem Van de Graaff accelerator at BNL. The primary objective of our studies is to elucidate the influence of high vs low energy deposition on track structure, delta ray contribution and resulting biological responses. These low energy ions are of special relevance as these energies may occur following absorption through the spacecraft and shielding materials in human tissues and nuclear fragments produced in tissues by high energy protons and neutrons. This study will help to verify the efficiency of these low energy particles and better understand how human cells respond to them. RESULTS

Physics,Environmental Science,Chemistry,Medicine,Biology
Evaluation and Analysis of Thermal Control Materials under Ground Simulation Test for Space Environment Effects

Youichi Nakayama,Kichiro Imagawa,Minoru Tagashira,Muneaki Nakai,Hisaaki Kudoh,Masaki Sugimoto,Noboru Kasai,Tadao Seguchi

DOI: https://doi.org/10.1088/0954-0083/13/3/334

IF: 1.73

2001-09-01

High Performance Polymers

Abstract:Thermal control materials such as white paint comprising silicone resin matrix (NASDA-1049/101-S), black paint comprising urethane resin matrix (NASDA-1049/201-U-I), aluminized polyimide adhesive tape (Sheldahl G408810) and silver-backed fluorinated ethylene propylene (silvered FEP) adhesive tape (Sheldahl G402500) were exposed to electron beam (EB), proton (H + ), iron ion (Fe 5+ ), ultraviolet (UV) and atomic oxygen (AO) radiation with ground simulation test facilities. Combined irradiation of EB → UV and another combined irradiation of EB → AO, where EB was irradiated at first and then UV or AO was irradiated, were also examined for white paint and black paint. Irradiation energies were 0.5 and 1.9 MeV for EB; 1, 3 and 10 MeV for H + ; 15 MeV for Fe 5+ ; equal to or larger than 3.1 eV for UV; and 5 eV for AO. Fluences of EB, H + and Fe 5+ were selected to simulate the environment of geostationary orbit (GEO) for 10 years. UV irradiation was equal to 300 equivalent solar days. AO fluence corresponded to the environment of low Earth orbit (LEO) for about 1 year. The solar absorptance (α S ) and normal infrared emittance (ε N ) of the examined materials both before and after irradiation were acquired. The durability of the materials against each irradiation treatment was judged by evaluating the changes in α S and ε N . White paint and black paint were strongly affected by AO, EB → UV, EB → AO and UV irradiation. White paint was also affected by EB and weakly by H + and Fe 5+ . Aluminized polyimide and silvered FEP were degraded most by AO and EB. EB had a stronger effect than ions (H + ,Fe 5+ ) in all the samples, the reason for which can be explained by the larger absorbed dose with EB compared with ions. The mass loss caused by the irradiation treatment was also measured for white paint and black paint. Analytical techniques such as scanning electron microscopy (SEM), electron spectroscopy for chemical analysis (ESCA) and Fourier transform infrared spectroscopy (FTIR) were applied to identify morphology and composition of the materials to obtain a deeper understanding of the mechanism of space environment effects on the materials.

polymer science
Characterising the energy deposition events produced by trapped protons in low earth orbit.

G. Anderson,L. W. Brackenbush,L. Braby

DOI: https://doi.org/10.1093/OXFORDJOURNALS.RPD.A080540

1989-10-01

Radiation Protection Dosimetry

Abstract:Men and equipment in space vehicles in low earth orbit are exposed to a wide variety of radiations, but the majority of the dose is due to trapped protons, which have energies of the order of 100 MeV and are low LET particles. These high energy particles produce nuclear fragmentation with high LET secondaries that may be responsible for a significant fraction of dose equivalent. In order to understand better the biological effectiveness of this radiation environment, a portable tissue equivalent proportional counter spectrometer has been developed that automatically records the distribution of energy in a small tissue-like site as a function of time. This instrument weighs about 700 g and will be flown on a number of future space shuttle flights.

Environmental Science,Medicine,Physics
Electron Radiation Effects on Candidate Solar Sail Material

David L. Edwards,Whitney S. Hubbs,George E. Wertz,David T. Hoppe,Mary K. Nehls,William A. Hollerman,Perry A. Gray,Charles L. Semmel

DOI: https://doi.org/10.1177/0954008304044106

IF: 1.73

2004-06-01

High Performance Polymers

Abstract:Solar sailing is a unique form of propulsion in which a spacecraft gains momentum from incident photons. Solar sails are not limited by reaction mass and provide continual acceleration, reduced only by the lifetime of the lightweight film in the space environment and the distance to the Sun. Once thought to be difficult or impossible, solar sailing has come out of science fiction and into the realm of possibility. Any spacecraft using this propulsion method would need to deploy a thin sail that could be as large as many kilometres in extent. The availability of strong, ultra lightweight, and radiation-resistant materials will determine the future of solar sailing. The National Aeronautics and Space Administration's (NASA) Marshall Space Flight Center (MSFC) is concentrating research into the utilization of ultra lightweight materials for spacecraft propulsion. The Space Environmental Effects Team at MSFC is actively characterizing candidate solar sail material to evaluate the thermo-optical and mechanical properties after exposure to space environmental effects. This paper will describe the irradiation of candidate solar sail materials to energetic electrons, in vacuum, in an effort to determine the in-space operational survivability of several candidate sail materials. Results from this research indicate that the candidate sail materials can survive significant doses of electron radiation while under high uniaxial stress.

polymer science
Radiation tests of a CubeSat OBC

Wolfgang Treberspurg,Rezaei Abbas,Robert Kralofsky,Andreas Sinn,Andreas Stren,Carsten Scharlemann

DOI: https://doi.org/10.1016/j.asr.2024.05.035

IF: 2.611

2024-05-23

Advances in Space Research

Abstract:Nano-satellites, which are following the CubeSat standard have established for demanding industrial and scientific applications with critical requirements on reliability and radiation tolerance. The employment of commercial off-the-shelf components enables a state-of-the-art performance but requires extensive testing to avoid and mitigate malefunctions due to the space environment. The CubeSat mission CLIMB is representative for future missions with a complex payload, a high power budget and a harsh radiation exposure. For this reason, a comprehensive irradiation study of its on-board-computer was done. The total ionizing dose damage of 50 krad was evaluated at a 60 Co source. As a consequence of this test, specific components were exchanged before performing single event effect studies at the synchrotron accelerator MedAustron. A board-level test revealed that the majority of effects concern the central micro controller wherefore was followed by a component-level test. Those irradiation tests make use of a pencil beam to map the device under test, which provides additional information to localize effects - by the timestamp - at the expense of an increased irradiation time compared to a homogeneous exposure. In this paper, we summarize the major findings of the test campaign and mitigation means and present a procedure for single event effect studies at medical accelerators.

geosciences, multidisciplinary,meteorology & atmospheric sciences,astronomy & astrophysics,engineering, aerospace
Micrometeoroid/space debris effects on materials

M. Finckenor,J. Zwiener

1993-12-01

Abstract:The Long Duration Exposure Facility (LDEF) micrometeoroid/space debris impact data has been reduced in terms that are convenient for evaluating the overall quantitative effect on material properties. Impact crater flux has been evaluated as a function of angle from velocity vector and as a function of crater size. This data is combined with spall data from flight and ground testing to calculate effective solar absorption and emittance values versus time. Results indicate that the surface damage from micrometeoroid/space debris does not significantly affect the overall surface optical thermal physical properties. Of course the local damage around impact craters radically alter optical properties. Damage to composites and solar cells on an overall basis was minimal.

Engineering,Materials Science,Physics
Determination of the Stopping Power and Failure-time of Spacecraft Components due to Proton Interaction Using GOES 11 Acquisition Data

N. N. Jibiri,Victor U. J. Nwankwo,Michael Kio

DOI: https://doi.org/10.48550/arXiv.1303.0434

2013-03-03

Abstract:One of the several ways to describe the net effect of charged-particles' interaction is the rate of energy loss along the particles' path. In this study, the mass stopping power (Sp) of selected spacecraft composite materials, through which the particle traverses, its range (R) and the distance (d) travelled (by the particles) through the materials have been calculated and analyzed. The dose (in Gy) as a function of particle flux and deposited energy was also determined. Predictions of their possible effects on space system operations and life-span were made, especially as values exceeded certain threshold (limit). Using GOES 11 acquired data for 3 months, estimations and/or calculations were made to determine the risk and safe period of a satellite in the geosynchronous orbit. Under certain space radiation environmental conditions (without mitigation of any sort), a spacecraft whose body is 20 mm thick and with Al alloy casing, was theoretically estimated to have a safe period of about 3 years and risk period of about 29 years (due to total ionizing dose) within which it would experience a catastrophic failure.

Space Physics
Space Environmental Effects on Multifunctional Radiation Shielding Materials

Subhayu Sen,John Scott O’Dell,Yongzhe Yan,Lawrence Heilbronn,Haibin Ning,Miria Finckenor,Meghan Carrico,Selvum Pillay

DOI: https://doi.org/10.1029/2024ea003681

IF: 3.68

2024-11-23

Earth and Space Science

Abstract:The two primary material requirements for a crewed habitat or spacecraft to operate beyond low earth orbit (LEO) include effective radiation shielding against the space radiation and secondary neutron environment and sufficient structural and thermal integrity. In this context it is mandatory to study the effect of long duration space environment on any proposed multifunctional radiation shielding material. In this paper we discuss two radiation shielding composite architectures and their long duration performance in LEO. Samples were flown on NASA's The Materials International Space Station Experiment (MISSE) platform and their structural, optical, and radiation shielding capabilities were characterized pre and post flight. Results showed composite architecture can be key in determining expected damage irrespective of sample placement orientation on the space station. A surface layer with a protective or sacrificial coating can be instrumental in minimizing property degradation even when exposed to orientations with high estimated sun hours and high fluence of atomic oxygen.

geosciences, multidisciplinary,astronomy & astrophysics
Assuring Radiation Tolerance of a Langmuir Probe Instrument for Low-Cost Interplanetary Missions

H. C. Valentine,A. Barjatya,R. M. Conway,R. E. Clayton,N. P. Graves,A. W. Bushmaker,J. L. Taggart,P. J. Edwards,A. W. Wright,A. D. Yarbrough

DOI: https://doi.org/10.1109/tns.2024.3455272

IF: 1.703

2024-10-22

IEEE Transactions on Nuclear Science

Abstract:With recent advancements in small-satellite technology and the onset of industry-wide budget constraints, the field of planetary space exploration has begun directing efforts toward the production of low-cost missions that are capable of achieving big-budget science objectives. For any interplanetary mission, radiation tolerance assurance is necessary to maximize the survivability of an instrument and characterize its measurement performance throughout the mission flight profile. In this work, the process of ensuring radiation tolerance is demonstrated for a suite of Langmuir probe instruments that will fly on NASA's upcoming dual small-satellite mission to Mars, the Escape and Plasma Acceleration and Dynamics Explorers (ESCAPADE). A case study is presented in radiation environment modeling, component selection, single-event effect (SEE) considerations, total ionizing dose (TID) testing practices, data processing, and risk assessment to demonstrate instrument performance assurance techniques that could apply to other similar low-cost interplanetary missions. It is shown that the ESCAPADE Langmuir probe (ELP) instrument design satisfies accuracy requirements after radiation testing up to 25 krad(Si). In addition, the viability of commercial components for long-duration space missions is discussed, and the results are presented for a low-cost analog-to-digital converter (ADC).

engineering, electrical & electronic,nuclear science & technology
Effect of He2+ ion irradiation on the mechanical properties of automated fibre placement (AFP) CF-PEEK thermoplastics composites

Ebrahim Oromiehie,Vishnu Nair,Ken Short,Tao Wei,Dhriti Bhattacharyya,B. Gangadhara Prusty

DOI: https://doi.org/10.1038/s41598-023-45742-8

IF: 4.6

2023-11-01

Scientific Reports

Abstract:Abstract Carbon fibre-reinforced polyetheretherketone (CF-PEEK) composites have gained significant usage across diverse industries like automotive and aerospace due to their desirable characteristics. These properties encompass recyclability, low density, high strength, wear resistance and thermal stability. The components made from CF-PEEK composites for space applications will be subjected to a high radiation environment due to the incoming cosmic rays, comprising protons, α particles, electrons, γ rays, etc., once they escape the Earth’s atmosphere. The ion irradiation of CF-PEEK is accompanied by radiation-induced effects, which drastically change the structure and properties of irradiated material. Since the resistance of CF-PEEK to radiation damage has not been studied extensively, this study aims to understand the effect of high-energy He 2+ ions on the microstructure and properties of CF-PEEK composites manufactured using automated fibre placement (AFP) under different processing conditions. The samples have been radiated with 5 MeV He 2+ ions using an energy degrader wheel to create a layer with relatively uniform damage. Then, were characterized using optical and scanning electron microscopy and their hardness was evaluated using nanoindentation. It was observed that, irradiation increases the hardness of the fibres in all cases. Also, fibre orientation affects the hardness in a statistically significant manner in both unirradiated and irradiated conditions.

multidisciplinary sciences
Incident beam current impact on space-charge retention in electron dynamitron irradiated polymethyl methacrylate

Kathryn M. Sturge,Noah Hoppis,Aneesh Anandanatarajan,Ariana M. Bussio,Bryson C. Clifford,Emily H. Frashure,Miriam E. Hiebert,James E. Krutzler,Timothy W. Koeth

DOI: https://doi.org/10.1063/5.0191534

IF: 6.6351

2024-03-01

APL Materials

Abstract:Dielectric charging aboard spacecraft and satellites is a persistent and pressing issue in materials design and applications. This study investigated the effect of electron irradiation on charge trapping and leakage properties in polymethyl methacrylate, which is necessary for determining the maximum permissible fluence of radiation before the material is pushed beyond its breakdown threshold in charged particle radiation-intense environments. It was observed that dielectric breakdown in the form of an electrostatic discharge event cannot be induced under the conditions of this experiment after an amount of time that is dependent on initial electron fluence. This time limit for which an electrostatic discharge can be induced was found to be longer for the lower beam current irradiations. The work presented here discusses the factors affecting charge leakage using a global electric field-driven model.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
First observations of enhanced low dose rate sensitivity (ELDRS) in space: One part of the MPTB experiment

J.L. Titus,W.E. Combs,T.L. Turflinger,J.F. Krieg,H.J. Tausch,D.B. Brown,R.L. Pease,A.B. Campbell

DOI: https://doi.org/10.1109/23.736514

IF: 1.703

1998-12-01

IEEE Transactions on Nuclear Science

Abstract:Bipolar devices, most notably circuits fabricated with lateral PNP transistors (LPNP) and substrate PNP transistors (SPNP), have been observed to exhibit an enhanced low dose rate sensitivity when exposed to ionizing radiation. These dose rate sensitive bipolar devices exhibited enhanced degradation of base current in transistors and of input bias current, offset current, and/or offset voltage in linear circuits at dose rates less than 0.1 rd(Si)/s compared to devices irradiated at dose rates greater than 1 rd(Si)/s. The total dose responses of several bipolar transistors and linear circuits in a space environment are demonstrated to exhibit enhanced degradation comparable, in magnitude, to ground-based data irradiated at a dose rate of 10 mrd(Si)/s indicating that enhanced low dose rate sensitivities (ELDRS) do indeed exist in space.

engineering, electrical & electronic,nuclear science & technology

The Aerospace Corporation’s Compendium of Recent Single Event Effect Results

Radiation-Induced Single-Event Effects on the Van Allen Probes Spacecraft

Irradiation Tests for Commercial Off-the Shelf Components with Atmospheric-like Neutrons and Heavy-Ions

Modeling the effects of low-LET cosmic rays on electronic components

Single Event Effect Testing With Ultrahigh Energy Heavy Ion Beams

Effects of Electron Beam and Atomic Oxygen Irradiation on Hypervelocity - Impact tested / Polyimide Coated Carbon Fiber-reinforced Plates

Investigation of Single-Event Effects for Space Applications: Instrumentation for In-Depth System Monitoring

Single-event effect testing of the PNI RM3100 magnetometer for space applications

Mitigating the effects of charged particle strikes on TES arrays for exotic atom X-ray experiments

Biological Effects of Particles with Very High Energy Deposition on Mammalian Cells Utilizing the Brookhaven Tandem Van de Graaff Accelerator

Evaluation and Analysis of Thermal Control Materials under Ground Simulation Test for Space Environment Effects

Characterising the energy deposition events produced by trapped protons in low earth orbit.

Electron Radiation Effects on Candidate Solar Sail Material

Radiation tests of a CubeSat OBC

Micrometeoroid/space debris effects on materials

Determination of the Stopping Power and Failure-time of Spacecraft Components due to Proton Interaction Using GOES 11 Acquisition Data

Space Environmental Effects on Multifunctional Radiation Shielding Materials

Assuring Radiation Tolerance of a Langmuir Probe Instrument for Low-Cost Interplanetary Missions

Effect of He2+ ion irradiation on the mechanical properties of automated fibre placement (AFP) CF-PEEK thermoplastics composites

Incident beam current impact on space-charge retention in electron dynamitron irradiated polymethyl methacrylate

First observations of enhanced low dose rate sensitivity (ELDRS) in space: One part of the MPTB experiment