Abstract:Polybutylene adipate-terephthalate (PBAT) is a fully biodegradable polyester, which has been proven to be the most suitable alternative to traditional plastics. However, due to the low strength of PBAT (17.2 MPa) and high price, the use of PBAT has a degree of limitations. To obtain a cost-effective and high-performance composite material of PBAT, for this study we selected microcrystalline cellulose, which is inexpensive and easily available, as the reinforcing medium. However, due to the hydrophobicity of PBAT, the mechanical properties of PBAT when mixed with hydrophilic cellulose were low. In order to improve the compatibility of cellulose and PBAT, this study selected hexadecyltrimethoxysilane (HDTMS) containing long carbon chains to silanize microcrystalline cellulose (MCC) to obtain silanized cellulose (SG). Three types of SGs with different degrees of silanization were obtained by controlling HDTMS with different mass ratios (1:10; 3:10; 5:10) to react with MCC. Characterization of these three types of SGs was conducted using FTIR, TEM, and water absorption analysis. The results demonstrated the successful synthesis of SG. With the increase in the reaction ratio of HDTMS and MCC, the size of the nanoparticles increases, and the water absorption decreases significantly. Subsequently, PBAT/SG composites were prepared by blending three kinds of silanized cellulose with PBAT in different proportions by the sol-gel method. To study the thermal stability and compatibility, the mechanical properties of the composites were evaluated, including thermogravimetric testing, scanning analysis, and dynamic thermomechanical testing. The optimal blending ratio and the optimal type of silane cellulose were found. Analysis of the mechanical properties revealed that the tensile strength initially increased and then decreased with increasing blending ratio for all three composites tested. Among them, the PBAT/SG2 composites exhibit superior performance, with a maximum tensile strength reaching 22 MPa at an 85/15 blending ratio, nearly 30% higher than that of pure PBAT alone. The addition of SG significantly improved the strength of the PBAT, and SG2 is more suitable for preparing high-strength composite materials. In addition, after the addition of SG, the yield stress of the composite is improved while maintaining good thermal stability. Both the SEM and DMA results indicated good compatibility of the PBAT/SG composites. This study provides a new idea for the industrial-scale development of degradable polyesters with low cost and good mechanical properties.

Preparation of carbodiimide-mediated octadecylamine modified carboxyethyl cellulose microfibrils and their reinforcement of poly(butylene adipate-co-terephthalate)

Manipulation of Crystallization Nucleation and Mechanical Properties of PBAT Films by Octadecylamine-Cellulose

Preparation of modified cellulose/PBAT films and its application in food preservation

Preparation and Mechanical Properties of PBAT/Silanized Cellulose Composites

Preparation and characterization of poly(butylene adipate‐co‐terephthalate) composites reinforced with acetylated cellulose nanocrystals and nanofibers for enhanced properties

Biodegradable Poly(butylene adipate- co -terephthalate) Nanocomposites Reinforced with In Situ Fibrillated Nanocelluloses

Cellulose Microfibrils Grafted with PBA Via Surface-Initiated Atom Transfer Radical Polymerization for Biocomposite Reinforcement.

Modification and characterizations of cellulose microfibril by atom transfer radical polymerization for biocomposites

Preparation, mechanical, and thermal properties of biodegradable polyesters/poly(lactic acid) blends

Insights into the enhanced mechanism of electron beam pretreatment on application performance for poly (butylene adipate-co-terephthalate)/ acetylated cellulose composite plastics

Development and Characterisation of Poly(butylene adipate-co-terephthalate)- Silane Modified Cellulose Nanocrystals Composite Materials and Films

Synthesis and characterization of bio‐based poly(ethylene 2,5‐furandicarboxylate)‐b‐poly(butylene adipate‐co‐terephthalate) copolymers

Interfacial interaction enhancement between biodegradable poly (butylene adipate-co-terephthalate) and microcrystalline cellulose based on covalent bond for improving puncture, tearing, and enzymatic degradation properties

Bio-based poly(butylene diglycolate-co-furandicarboxylate) copolyesters with balanced mechanical, barrier and biodegradable properties: A prospective substitute for PBAT

Poly(butylene Adipate-Co-terephthalate)-quaternary Ammonium Copolyester with Highly Enhanced Mechanical Performance Through Synergistic Cation-π and Hydrogen-Bonding Interactions

Xylan cinnamoylation for reinforcing poly (butylene adipate-co-terephthalate): Molecule design and interaction optimization

Effects of Wood Content and Modification on Properties of Wood Flour/Polybutylene Adipate Terephthalate Biocomposites

Foaming Behaviors of Poly (butylene Adipate-Co-terephthalate) with Methyl Methacrylate-Co-glycidyl Methacrylate As Chain Extender

Highly Enhanced Mechanical Strength and Toughness of Biodegradable PBAT Plastics Through a Biobased Multiple Hydrogen Bonding Strategy

Enhanced Crystallization of Poly(butylene adipate-co-terephthalate) by a Self-assembly Nucleating Agent

Effect of Carbon Black and Chain Extender on Thermal, Rheological and Mechanical Properties of Fully Biodegradable Poly(butylene Adipate‐co‐terephthalate)/poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) Blends