Abstract:The effects of a minor Zn addition on the mechanical and corrosion properties and microstructure of a high Mg content AlMg alloy containing Er and Zr in the warm-rolled state were studied using tensile test, nitric acid mass loss test (NAMLT), exfoliation corrosion susceptibility test (ASSET), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques. The tensile test results showed that the 0.58 wt% Zn addition to the Al-Mg-Er-Zr alloy increased the yield strength from 297 to 351 MPa and tensile strength from 416 to 445 MPa, but decreased the elongation from 13.3 % to 12.5 %. The NAMLT and ASSET results showed that the two warm rolled alloys were initially in the stabilization state, but the Al-Mg-Er-Zr alloy without Zn added became sensitized severely after the accelerated sensitization annealing (ASA) at 100 °C. The Zn addition improved the intergranular corrosion (IGC) resistance and exfoliation corrosion (EC) resistance significantly. The TEM results showed that, for the Al-Mg-Er-Zr alloy, there were Al 3 (Er,Zr) phase particles in the matrix and β (Al 3 Mg 2 ) phase particles separated from each other at the grain boundary. After the ASA treatment, more β phase particles were precipitated and covered the grain boundary completely. For the Al-Mg-Zn-Er- Zr alloy, another nanoscale T (Al 32 (Mg, Zn) 49 ) phase was precipitated in the matrix, and there were no grain boundary phase particles observed at the grain boundary, because the precipitation of T phase consumed the supersaturated Mg in the matrix, thus suppressing the formation of grain boundary phase particles during the ASA treatment and resulting in a good corrosion resistance. The strengthening effect of the Zn addition was mainly due to the formation of T phase particles during the warm rolling process.

Effects of L1 2 precipitates containing Zr, Er, and Y on the precipitation of Al–Zn–Mg alloys at elevated temperatures

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Effects of addition of Er and Zr on microstructure and mechanical properties of Al–Cu–Mn–Si–Mg alloy

Effect of Y on Age Hardening Response and Mechanical Properties of Mg-xY–1.5LPC −0.4zr Alloys

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Effects of yttrium additions on microstructures and mechanical properties of cast Al-Cu-Mg-Ag alloys

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Effects of Zr+Er and Zr+Y on Microstructure and Tensile Properties of Al-Mg-Si-Cu-Mn-Cr Alloys

Investigation of Atomic-Scale η1 Precipitate Growth in Aluminum-Zinc-Magnesium Alloys

Effect of Ag addition on the age hardening and precipitation behavior in an Al-Cu-Li-Mg-Zn-Mn-Zr alloy

Atomic-scale characterization of V-shaped interface structure of η 1 precipitates in Al–Zn–Mg alloy

Effects of precipitates and solute atoms on the work hardening and softening behavior of Zn-rich aluminum alloy

Microstructure and Precipitates in Mg-Zn-Y Alloys

Effects of minor Nd and Er additions on the precipitation evolution and dynamic recrystallization behavior of Mg–6.0Zn–0.5Mn alloy

Study on the strengthening mechanism of rare earth yttrium on magnesium alloys

Influence of Zr addition on the morphology of primary MgZn 2 in the solidification microstructure of Zn-6Al-3Mg alloy

Unveiling precipitation behavior in Mg-Y based alloys

Micro-alloying effects of Mn and Zr on the evolution of ageing precipitates and high temperature strength of Al-11.5Si–4Cu alloy after a long-time heat exposure

Co-precipitation of T′ and η′ phase in Al-Zn-Mg-Cu alloys

The influence of Zn addition on the microstructure and mechanical and corrosion properties of warm rolled Al mg alloys containing Er and Zr

Effects of extrusion ratio and temperature on the microstructure and mechanical properties of Mg–Zn–Yb–Zr extrusion alloys