Abstract:Nano spray drying has emerged as an outstanding platform for engineering micro- and nanoparticles, with growing applications in various areas of drug delivery. As a new technology involving distinct technical design, parameters of the nano spray drying process are not fully elucidated. In a quality-by-design approach, the aim of the current study was to gain thorough understanding of critical determinants of product characteristics in the Büchi Nano Spray Dryer B-90. Following a factorial experimental design, a series of spray drying experiments were conducted to gain new insights into the influences of the inlet temperature, the spray solvent, and the solute concentration in the spray solution on the yield, the moisture content, and the particle size of the nano spray-dried powder material. Special consideration was given to the potential of using hydroethanolic in comparison with aqueous solvent systems and to particle engineering for pulmonary drug delivery. Lactose and mannitol, widely used as excipients in dry powder inhalation formulations, were used as model materials. Lactose and mannitol are known to spray dry in amorphous and crystalline forms, respectively. The yields of spray drying of lactose and mannitol amounted generally to 71.1 ± 6.6% w/w and 66.1 ± 3.5% w/w, respectively. The spray-dried materials exhibited generally a number-weighted median particle diameter of 1.6 ± 0.2 μm and a volume-weighted median particle diameter of 5.1 ± 1.0 μm. A detailed analysis of the results improved understanding of the interplay between process parameters in the Nano Spray Dryer. The results demonstrate that optimization of spray generation is the key to yield optimization. On the other hand, particle size is determined by the spray mesh pore size and the spray solution degree of saturation. Selection of an appropriate spray solvent and using spray solution additives could optimize spray flow. In parallel, the spray solvent and the solute concentration in the spray solution determine the degree of saturation. Guidance on optimization of particle engineering by nano spray drying is provided.

Experimental Investigation of Spray Drying Breakup Regimes of a PVP-VA 64 Solution Using High-Speed Imaging

Evaluation of a Three-Fluid Nozzle Spraying Process for Facilitating Spray Drying of Hydrophilic Polymers for the Creation of Amorphous Solid Dispersions

Numerical Models For Viscoelastic Liquid Atomization Spray

Primary spray break-up from a nasal spray atomizer using Volume of Fluid to Discrete Phase Model

Theoretical Probing of the Phenomenon of the Formation of the Outermost Surface Layer of a Multi-Component Particle, and the Surface Chemical Composition after the Rapid Removal of Water in Spray Drying

Spray Drying of PEG6000 Suspension: Reaction Engineering Approach (REA) Modeling of Single Droplet Drying Kinetics

Experimental investigation and modeling of atomization aspects in spray drying for production of pharmaceuticals with inhalable size

Data-Driven Modeling of the Spray Drying Process. Process Monitoring and Prediction of the Particle Size in Pharmaceutical Production

Experimental Research of Effervescent Atomization of High Viscosity Fluids

Ultrasonic spray freeze-drying of sucrose and mannitol-based formulations: Impact of the atomization conditions on the particle morphology and drying performance

Breakup Mechanisms in Air-Assisted Atomization of Highly Viscous Pyrolysis Oils

Design of experiments utilization to map the processing capabilities of a micro-spray dryer: particle design and throughput optimization in support of drug discovery

Particle Engineering by Nano Spray Drying: Optimization of Process Parameters with Hydroethanolic versus Aqueous Solutions

Effect of the Addition of Diblock Copolymer Nanoparticles on the Evaporation Kinetics and Final Particle Morphology for Drying Aqueous Aerosol Droplets

Co-spray Drying Drugs with Aqueous Polymer Dispersions (APDs)—a Systematic Review

Mechanistic Formulation Design of Spray-Dried Powders

Drop breakup dynamics of dilute polymer solutions: Effect of molecular weight, concentration, and viscosity

Effect of droplet collisions on evaporation in spray-drying

Understanding the operating limitations of an internal-mixing Air-Core-Liquid-Ring (ACLR) nozzle for process intensification in spray drying

Measurement of low amounts of amorphous content in hydrophobic active pharmaceutical ingredients with dynamic organic vapor sorption

Are traditional small-scale screening methods reliable to predict pharmaceutical spray drying?