Abstract:Because of the promising corrosion resistance and load-bearing capacity, titanium-clad (TC) bimetallic steel has gained increasing attention in ocean/coastal civil and structural engineering. Due to the double-layer nature of TC bimetallic steel, the characteristics of the structural member’s geometry and weld details are considerably different from that of conventional steel members. Even though previous studies have conducted systematical clarifications on parent material of TC bimetallic steels, the mechanical behaviors of weld joints are still vague. This paper firstly describes the manufacture features of TC bimetallic steel welded joints and welded members. Subsequently, the type II and type III butt-welded joints provided by GB/T 13149-2009 are selected to study the corresponding tensile mechanical behavior. Two butt-welded TC bimetallic steel plates were fabricated from hot-rolled bonding TA2 + Q355B TC bimetallic steel and welding wire of ER55-Ni1 and ERTA2ELI. Eight tensile coupons were then extracted from the two welded plates and loaded to failure monotonically. The failure mechanism, stress–strain curves and key mechanical properties are studied and compared with that of parent material. It is found that both types of welded joints possess two fracture points. The first one refers to the fracture of weld joint between the clad layer and titanium cover plate, whilst the second one is the eventual fracture of substrate metal. When the first fracture point is reached, the stress–strain relation exhibits a sharp drop in stress value. Thereafter, a strain-hardening behavior can still be observed prior to the ultimate strength point. The first fracture-induced stress drop of type II joint is less than that of type III joint, whilst the strain-hardening amount of type II joint is more outstanding than that of type III joint. The fracture elongations of type II joint and type III joint are respectively 37% and 57% that of the parent material, whilst the proportions between the ultimate strengths of welded joints and parent material are, respectively, 90% and 93%. In general, the two types of TC bimetallic steel weld joints investigated herein exhibit favorable load-bearing capacity but unfavorable ductility and deformability. Based upon the experimental results, the structural design methodology of welded TC bimetallic steel structure is discussed. The investigations conducted in this paper can provide reference for development of structural design theory of welded TC bimetallic steel structure.

Transverse heterogeneity of bonding strength in Ti/steel clad plates fabricated by hot rolling with bimetal assembling

Evolution mechanism of microstructure and bond strength based on interface diffusion and IMCs of Ti/steel clad plates fabricated by double-layered hot rolling

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Effect of rolling temperature on microstructure and mechanical properties of Ti/steel clad plates fabricated by cold spraying and hot-rolling

Intergrowth Bonding Mechanism and Mechanical Property of Linear Friction Welded Dissimilar Near‐Alpha to Near‐Beta Titanium Alloy Joint

Microstructural evolution and mechanical properties in the partial transient liquid phase diffusion bonding of tungsten to steel

Microstructures and Tensile Behaviors of Stainless Steel Clad Plate

Interface formation and bonding mechanisms of hot-rolled stainless steel clad plate

Interfacial microstructure and mechanical properties of stainless steel clad plate prepared by vacuum hot rolling

Insights into microstructure evolution and fracture mechanisms of welded joints of high strength steel patchwork components

Enhanced Mechanical Properties of Ti/Mg Laminated Composites Using a Differential Temperature Rolling Process under a Protective Atmosphere

Deformation law and bonding mechanism of 45 carbon steel/316 L stainless steel cladding tubes fabricated by three-roll skew rolling bonding process

Hot roll bonding between commercially pure titanium and high-strength low-alloy steel using Fe interlayer

Interfacial microstructure and mechanical properties of titanium/steel dissimilar joining

Tensile Behavior of Titanium-Clad Bimetallic Steel Butt-Welded Joints

Interlayer Engineering for Titanium Clad Steel by Hot Roll Bonding

Effect of cumulative deformation and interlayer mechanical properties on bonding strength of corrugated interface steel/aluminum composite plate

Deformation Mechanism and Microstructure Evolution in Stainless Steel Clad Plate of Longitudinal Corrugated Hot Rolling

Weld Formation Mechanism and Microstructural Evolution of TC4/304 Stainless Steel Joint with Cu-Based Filler Wire and Preheating

Microstructure and mechanical properties of stainless steel clad plate joints produced by TIG and MAG hybrid welding

Velocity Field Analysis of Bonding Interface on Cold-Rolled Copper/Aluminum Composite Plate