Multi-Scale modelling of structure-property relationship in additively manufactured metallic materials

Haibin Tang,Haijun Huang,Changyong Liu,Zhao Liu,Wentao Yan

DOI: https://doi.org/10.1016/j.ijmecsci.2020.106185

IF: 7.3

2021-03-01

International Journal of Mechanical Sciences

Abstract:<p>This paper presents a multi-scale modelling framework to evaluate the structure-property relationship of metallic materials fabricated by powder-bed additive manufacturing (AM) technique based on crystal plasticity finite element methods. In this framework, a new synthetic microstructure generation approach is proposed to reconstruct micro-scale models of AMed metals according to the characteristics of grain growth in the fabrication process. The constitutive relation of individual grains in the micro-scale reconstructed models is described with the single-crystal-scale plasticity model. Meanwhile, to reduce the computational cost, a polycrystal-scale plasticity model is also established. The homogeneous elastic moduli tensor is computed according to Mori-Tanaka's theory, while the plastic deformation is described by the equivalent grain set. The proposed multi-scale modelling framework is validated against experiments, where the as-built Ti-6Al-4V samples fabricated by selective laser melting (SLM) are tested under uniaxial tensile, compressive, and cyclic loadings. The presented experimental and computational study demonstrates the capability of the proposed multi-scale modelling framework in the structure-property analysis of AMed metals.</p>

engineering, mechanical,mechanics

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to evaluate the structure - property relationship of metal materials fabricated by powder - bed additive manufacturing (AM) technology through a multi - scale modeling framework. Specifically, the paper aims to provide a rapid computational evaluation method to understand the influence of microstructural characteristics on the mechanical properties of metal materials during the additive manufacturing process.

### Main problems and solutions

1. **Microstructure generation**:
- The paper proposes a new synthetic microstructure generation method for reconstructing the micro - model of AM metals according to the grain growth characteristics during the additive manufacturing process. This method takes into account the unique grain growth features in the AM process, such as temperature gradient, scanning direction, etc.

2. **Single - crystal - scale plasticity model**:
- In order to describe the deformation behavior of each grain in the micro - reconstruction model, the paper adopts a single - crystal - scale plasticity model. This model is based on the crystal plasticity finite element method (CPFEM) and simulates the anisotropic plastic deformation based on the slip mechanism.

3. **Polycrystalline - scale plasticity model**:
- In order to reduce the computational cost, the paper also establishes a polycrystalline - scale plasticity model. This model uses the Mori - Tanaka theory to calculate the homogenized elastic modulus tensor and describes the plastic deformation through equivalent grain sets.

### Verification and application
- The proposed multi - scale modeling framework has been verified by experimental data, especially through uniaxial tensile, compressive, and cyclic loading tests on Ti - 6Al - 4V samples fabricated by selective laser melting (SLM). The experimental and computational results show that this framework has good capabilities in the structure - property analysis of AM metals.

### Key formulas

- **Decomposition of deformation gradient**:
\[
F = F^e\cdot F^p
\]

- **Velocity gradient**:
\[
L=\dot{F}\cdot F^{- 1}
\]

- **Plastic velocity gradient**:
\[
L^p=\sum_{\alpha = 1}^{N}\dot{\gamma}^{(\alpha)}m^{(\alpha)}\otimes n^{(\alpha)}
\]

- **Relationship between Jaumann stress rate and shear strain rate**:
\[
\begin{aligned}
&\dot{\sigma}^e = C:D^e\\
&D^p=\sum_{k = 1}^{N_2}f_k\sum_{\alpha = 1}^{N_1}\dot{\gamma}^{(\alpha)}P^{(\alpha)}\\
&W^p=\sum_{k = 1}^{N_2}f_k\sum_{\alpha = 1}^{N_1}\dot{\gamma}^{(\alpha)}W^{(\alpha)}
\end{aligned}
\]

- **Calculation of elastic modulus tensor**:
\[
C_{\text{eq}}=\sum_{k = 1}^{N}f_kC_k
\]

Through these methods and models, the paper provides a powerful tool for understanding the relationship between the microstructure of additive - manufactured metal materials and their mechanical properties.