Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

Conceptual design of the blanket mechanical attachment for the helium-cooled lithium–lead reactor

Pre-conceptual Design and Proof of Principle Assessments of Self-Cooled Toroidally Symmetric Lead-Lithium (TSLL) Blanket

ITER blanket engineering challenges and solutions

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Compact fusion blanket using plasma facing liquid Li-LiH walls and Pb pebbles

Preliminary Design of A Solid Particulate Cooled Blanket for the Steady-State Tokamak Reactor (Sstr)

Thermal Analysis of HCSB Blanket Concept for a Moderate Sized Tokamak Fusion Reactor

Helium-Cooled Solid Breeder Blanket Design for a Tokamak Fusion Reactor

Blanket and shield design for a noncircular Tokamak experimental power reactor

Neutronic Assessment of Candidate Materials for TF Coils Shielding in a DEMO Fusion Reactor Based on a DCLL Blanket

Design and Analysis of “Filling-Evacuating” High-Pressure Helium-Cooled Loop

Structure Optimization of Helium-Cooled Blanket for Fusion Reactor Based on Three-Dimensional Full-Scale Thermal-Hydraulic Analysis

Progress in design and experimental activities for the development of an advanced breeding blanket

Studies on Flibe Blanket Designs in Helical Reactor FFHR

Conceptual design study on fusion-based hydrogen production reactor

Conceptual Design and Comprehensive Optimization Analysis of a Fusion-Fission Hybrid Reactor Water-Cooled Pressure Tube Blanket

Thermal Hydraulic Analysis on the Water Lead Lithium Cooled Blanket for CFETR

ARIES-I SiC Composite Low Activation Blanket Design

Conceptual Design and Neutronics/Thermal-Hydraulic Coupling Optimization Analyses of Two Typical Helium Cooled Solid Breeder Blanket Modules for CFETR Phase II

Engineering design of the ITER blanket and relevant research and development results

Conceptual Design of the Supercritical CO2 Cooled Lithium Lead Blanket for CFETR