Abstract:In deep underground engineering, circular roadways are widely used; many rock engineering problems can usually be simplified as mechanical analysis of rock structures with holes. To reveal the influence of intrahole reinforcement on the mechanical properties of rock with a single hole, this paper takes the single-hole rock-like material specimens with different reinforcement conditions as the research object. The RYL600 rock shear rheometer was used to conduct biaxial compression tests and, combined with HD industrial cameras and high-precision strain gauges, to study the effects of different reinforcement thicknesses and different lateral pressure on the mechanical properties of single-hole rock-like materials during the total stress and strain process. The thickness of the reinforced aluminum alloy pipe in the whole test is divided into four types: 0, 1, 1.5, and 2 mm. Under different reinforcement conditions, it is divided into 4 series of 0, 0.5, 1, and 1.5 MPa according to the different lateral pressure. Research shows the following: (1) Under the same lateral pressure, as the reinforcement thickness of the aluminum alloy tube increases, the reinforcement effect of the aluminum alloy tube on the specimen increases, and the strength of the reinforced specimen is increased by 1.42%~33.04% compared with the strength of the unreinforced specimen; under the same reinforced thickness of the aluminum tube, the peak strength of the specimen increases with the increase of lateral pressure, and the peak strength of the specimen with lateral pressure is 3.34%~50.26% higher than that of the specimen without lateral pressure. (2) Increasing the lateral pressure can significantly reduce the primary tensile cracks of the specimen. As the reinforcement thickness increases, the primary tensile cracks and remote cracks of the specimen are significantly reduced, and the failure surface of the specimen gradually tends to the middle of the sample. (3) The failure modes of specimens with holes can be divided into five types: single bevel type I, single bevel type II, single bevel type III, bevel T type, and single part shear type. All of these five failure modes are shear cracks that develop into fracture surfaces, while remote cracks and primary tensile cracks do not develop into fracture surfaces.

Strength and deformation behaviors of bedded rock mass under bolt reinforcement

Study on the Bolt-mesh-anchor Surrounding Mechanism of a Roadway in a Soft and Thick Rock Seam

Strength and Failure Behaviors of a Jointed Rock Mass Anchored by Steel Bolts: A Numerical Modeling Study

Research on the Stress Distribution Law of Fully Anchored Bolt and Analysis of Influencing Factors under the Condition of Surrounding Rock Deformation

Experimental and numerical investigations on mechanical property and reinforcement effect of bolted jointed rock mass

Shear Behavior of Bolt-Reinforced Joint Rock Under Varying Stress Environment

Mechanical Behaviour of a Deep Soft Rock Large Deformation Roadway Supported by NPR Bolts: A Case Study

Coupled rheological behavior of tunnel rock masses reinforced by rock bolts based on the non-hydrostatic stress field

Experimental Study on the Mechanical Behavior of Rock Bolts Subjected to Complex Static and Dynamic Loads

Influence of anchorage length and pretension on the working resistance of rock bolt based on its tensile characteristics

Deformation and failure characteristics of anchorage structure of surrounding rock in deep roadway

Coupling Rheological Behavior of Rock Mass Supported with Rockbolts Based on the Point Load Model

Study on the anchorage mechanism and roof stability control technology of bolts in fractured or weak surrounding rock

Bearing Characteristics of Surrounding Rock of Deep Mining Roadway with Full and End Bolt Anchorages: A Comparative Numerical and Experimental Study

Constitutive behavior of reinforced rock unit anchored by an energy-absorbing bolt

Experimental Study on the Shear Deformation Characteristics and Mechanical Properties of Bolted Joints

Study on Stability Control Mechanism of Deep Soft Rock Roadway and Active Support Technology of Bolt-Grouting Flexible Bolt

Experimental Studies on Cracking and Local Strain Behaviors of Rock-Like Materials with a Single Hole before and after Reinforcement under Biaxial Compression

Mechanical testing and numerical simulation of intelligent terminal structure of rockbolt used as a deformable support and for safety monitoring in rock engineering

Mechanical Properties and Failure Mechanism of Anchored Bedding Rock Material under Impact Loading

Research on the Propagation Law of Stress Wave in Rock Mass Supported by Bolt under Dynamic Load