Abstract:Clarifying the influences of anchorage parameters on rock mass deformation and failure under impact dynamic load is the key to the control of surrounding rock in rock burst roadways. However, the existing research mainly focuses on the influence of anchorage parameters on rock mass deformation and failure under static load. However, the research on the dynamic failure mechanism of rock mass remains insufficient. According to the deformation and failure characteristics of anchor structure in practical engineering, the dynamic response law of the anchored rock mass under lateral impact load was studied through indoor similar physical model tests. Besides, the effects of anchor material, prestress and anchorage method on crack propagation mode and dynamic mechanical characteristics of anchored rock mass were analyzed. The lateral impact mechanical model of the anchored rock mass was established. Furthermore, rational suggestions on anchorage support in deep rock burst roadways were put forward based on the impact failure mechanism of prestressed anchored rock mass. The following research results were yielded: Under impact load, the cracks of the anchored rock mass are concentrated around the impact point, and the rock sample mainly undergoes shear failure and tensile failure. The size of cracks is controlled by the anchor material, the anchoring method and the prestress level. The axial force of the bolt increases with the increase of steel strength. The axial force platform segments of HRB400, HRB500, and CRM700 bolts are 20.84kN, 20.95kN, and 45.65kN, respectively. The material of the bolt has a significant impact on the impact resistance of the rock mass. The high strength of the bolt increases the stiffness of the anchored rock mass, and the impact force and axial force of the bolt are more sensitive to the impact load. When the pre-stress of the bolt increases from 15 to 45kN, the impact force action time decreases from 47 to 16ms, and the impact force platform value increases from 24.54 to 30.60kN. The impact force change is not significant, but the impact force action time changes more significantly. High pre-stress can improve the deformation resistance of the rock mass, but it will reduce the bearing capacity and impact resistance of the anchor structure. There is also a significant difference in the axial force of the bolt between the full length anchoring and end anchoring methods. The axial force of the bolt under the full-length anchoring method shows a slow increasing trend, and the axial force of the bolt under end anchoring is similar to its static load mechanical characteristic curve. compared with end anchorage, the rock mass is of greater stiffness and deforms less severely under full-length anchorage; meanwhile, the bolt can absorb massive energy through its elongation, but it tends to break under dynamic load. For deep rock burst roadways, it is suggested to choose "three-high" bolts (cables) as the supporting material, reduce the dynamic and static loads of surrounding rock and improve the mechanical properties of surrounding rock, to weaken the influence of dynamic load on the supporting structure of the anchored surrounding rock. The research results provide some theoretical guidance for the design of anti-burst bolt support in deep rock burst roadways.

Constitutive behavior of reinforced rock unit anchored by an energy-absorbing bolt

Development of a Unified Rock Bolt Model in Discontinuous Deformation Analysis

Coupled rheological behavior of tunnel rock masses reinforced by rock bolts based on the non-hydrostatic stress field

Evolution and Control Mechanism of Rockburst in Rock Anchored by New Energy-Absorbing Material

Strength and deformation behaviors of bedded rock mass under bolt reinforcement

Experimental study on lateral impact resistance of the prestressed anchored rock mass

Mechanical anchoring mechanism of prestressed bolt for rock-coal-bolt combination under uniaxial compression

Mechanical Behaviour of a Deep Soft Rock Large Deformation Roadway Supported by NPR Bolts: A Case Study

Evaluation of the performance of yielding rockbolts during rockbursts using numerical modeling method

Study on Mechanical Characteristics of Energy-Absorbing and Anti-Scour Bolts

A novel constitutive law of confined grouted rock bolt under pull-out load based on a fully nonlinear bond-slip model

Experimental Studies on Cracking and Local Strain Behaviors of Rock-Like Materials with a Single Hole before and after Reinforcement under Biaxial Compression

Investigation into the time-dependent mechanical behavior of pre-stressed anchor bolts and fractured rock specimens under synchronized tensile loads

Coupling Rheological Behavior of Rock Mass Supported with Rockbolts Based on the Point Load Model

Yieldable technology of lengthened bolts for high-stress soft rock roadways

Research on the Stress Distribution Law of Fully Anchored Bolt and Analysis of Influencing Factors under the Condition of Surrounding Rock Deformation

Numerical Analysis of Mechanical Characteristics of Constant-Resistance, Energy-Absorbing and Anti-Scour Bolts

Anchorage mechanism of bamboo-steel composite rockbolts subjected to the coupled effect of tensile and shear stress

Experimental and numerical investigations on mechanical property and reinforcement effect of bolted jointed rock mass

Mechanical behavior of soft rock roadway reinforced with NPR cables: A physical model test and case study

Evaluation of the Effects of Yielding Rockbolts on Controlling Self-Initiated Strainbursts: A Numerical Study