Abstract:Low-cycle fatigue (LCF) behavior of nickel-based precipitation-strengthened superalloy GH4145/SQ was investigated systematically under fully reversed total strain amplitude control conditions at 538°C in laboratory air. It was shown that the alloy exhibited a pronounced initial fatigue hardening followed by continuous fatigue softening to failure at high strain amplitudes, while at low strain amplitudes the initial hardening was followed by a well-defined saturation stage. Microstructure observations using optical and transmission-electron microscopy revealed that slip band density increased with increasing total strain amplitudes and the size of the γ′precipitates tended to reduction due to repeated shearing by the dislocations with continuous cyclic straining. The above changes in microstructures during cycling were essentially responsible for the fatigue hardening–softening behavior of the alloy. Both optical and SEM micrographs indicated that at low strain amplitudes crack propagation was basically transgranular, while at high strain amplitudes crack propagation was essentially intergranular. Bilinear behavior with a change of slope at a plastic strain amplitude of about 0.2pct was observed in cyclic stress–strain (CSS), Coffin–Manson (C–M) and plastic strain energy–life plots. A change in the number of operating slip systems and the fracture modes with the strain amplitude employed was used to explain this two-slope characteristic. In both the companion specimens test (CST) and the incremental step test (IST) methods the alloy exhibited non-masing type behavior. It was suggested that, for the first approximation, the half-life plastic strain energy could be calculated directly according to the equation without reckoning in the non-masing behavior.

Improving the stress-controlled fatigue life of low solid-solution hardening Ni-Cr alloys by enhancing short range ordering degree

Short-range ordering plays a determining role in the low-cycle fatigue life improvement of fcc metals: A conclusive study on low solid-solution hardening Ni-Cr alloys

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

Effect of Short-Range Ordering on the Grain Boundary Character Distribution Optimization of FCC Metals with High Stacking Fault Energy: A Case Study on Ni-Cr Alloys

Enhancing the Fatigue Resistance of High and Medium Entropy Alloys by Manufacturing-Driven Microstructural Developments

Molecular dynamics study of fatigue mechanical properties and microstructural evolution of Ni-based single crystal superalloys under cyclic loading

In situ neutron diffraction study of fatigue behavior of CrFeCoNiMo0.2 high entropy alloy

Tuning Chemical Short-Range Order for Simultaneous Strength and Toughness Enhancement in NiCoCr Medium-Entropy Alloys

Fatigue-resistant design in low-cycle regime by regulating the micro-structural gradient in a TWIP steel: Modelling and experiment

Low cycle fatigue behaviors of CrCoNi medium-entropy alloy with different grain sizes

Effect of elevated temperature on high-cycle and very-high-cycle fatigue properties of Ni-based superalloy manufactured by selective laser melting

Fretting Fatigue Experiment and Polycrystal Plasticity Simulation in Ni-based Superalloy at Room Temperature and 650 °C

Effect of Stress Ratio on Very High Cycle Fatigue Properties of Ti-10V-2Fe-3Al Alloy with Duplex Microstructure

Low cycle fatigue behavior of precipitation-strengthened Cu-Cr-Zr contact wires

Evolution of fatigue mechanical properties and micro defects in nickel-based single crystal superalloys: A molecular dynamics research

Composition-dependent slip planarity in mechanically-stable face centered cubic complex concentrated alloys and its mechanical effects

Enhanced low-cycle fatigue and crack propagation resistance of an Al-Cu-Mg-Si forging alloy by non-isothermal aging

Fatigue Crack Growth Behavior of Beta-Annealed Ti–6Al–2Sn–4Zr–xMo (x = 2, 4 and 6) Alloys: Influence of Microstructure and Stress Ratio

Low cycle fatigue performances of Al 0.3 CoCrFeNi high entropy alloys: In situ neutron diffraction studies on the precipitation effects

Influence of microstructure on strain controlled low cycle fatigue crack initiation and propagation of Ti-55531 alloy