Abstract:In this study, a novel perovskite solar cell (PSC) architecture is presented that utilizes an HTL-free configuration with formamide tin iodide (FASnI3) as the active layer and fullerene (C60) as the electron transport layer (ETL), which represents a pioneering approach within the field. The elimination of hole transport layers (HTLs) reduces complexity and cost in PSC heterojunction structures, resulting in a simplified and more cost-effective PSC structure. In this context, an HTL-free tin HC(NH2)2SnI3-based PSC was simulated using the solar cell capacitance simulator (SCAPS) within a one-dimensional framework. Through this approach, the device performance of this novel HTL-free FASnI3-based PSC structure was engineered and evaluated. Key performance parameters, including the open-circuit voltage (Voc), short-circuit current density (Jsc), fill factor (FF), power conversion efficiency (PCE), I-V characteristics, and quantum efficiency (QE), were systematically assessed through the modulation of physical parameters across various layers of the device. A preliminary analysis indicated that the HTL-free configuration exhibited improved I-V characteristics, with a PCE increase of 1.93% over the HTL configuration due to improved electron and hole extraction characteristics, reduced current leakage at the back contact, and reduced trap-induced interfacial recombination. An additional boost to the device's key performance parameters has been achieved through the further optimization of several physical parameters, such as active layer thickness, bulk and interface defects, ETL thickness, carrier concentration, and back-contact materials. For instance, increasing the thickness of the active layer PSC up to 1500 nm revealed enhanced PV performance parameters; however, further increases in thickness have resulted in performance saturation due to an increased rate of hole-electron recombination. Moreover, a comprehensive correlation study has been conducted to determine the optimum thickness and donor doping level for the C60-ETL layer in the range of 10-200 nm and 1012-1019 cm-3, respectively. Optimum device performance was observed at an ETL-C60 ultra-thin thickness of 10 nm and a carrier concentration of 1019 cm-3. To maintain improved PCEs, bulk and interface defects must be less than 1016 cm-3 and 1015 cm-3, respectively. Additional device performance improvement was achieved with a back-contact work function of 5 eV. The optimized HTL-free FASnI3 structure demonstrated exceptional photovoltaic performance with a PCE of 19.63%, Voc of 0.87 V, Jsc of 27.86 mA/cm2, and FF of 81%. These findings highlight the potential for highly efficient photovoltaic (PV) technology solutions based on lead-free perovskite solar cell (PSC) structures that contribute to environmental remediation and cost-effectiveness.

Investigating a Pb-free n-i-p perovskite solar cell with BFCO absorber using SCAPS-1D

Current Status of Pb-free PSCs and Infer the Highest Achievable PCE Via Numerical Modeling, and Optimization of Novel Structure FAMASnGeI3 Based PSCs

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Exploration of the Photovoltaic Properties of Oxide-based Double Perovskite Bi2FeCrO6 using an amalgamation of DFT with Spin-Orbit Coupling Effect and SCAPS-1D Simulation Approaches

Numerical Simulation and Optimization of Highly Stable and Efficient Lead-Free Perovskite FA1−xCsxSnI3-Based Solar Cells Using SCAPS

Theoretical Analysis on Interfacial Dynamics Between Charge Transport Layer and Different Absorbers in Pb-free All Inorganic Perovskites Solar Cells

Design and simulation of CsPb.625Zn.375IBr2-based perovskite solar cells with different charge transport layers for efficiency enhancement

Numerical simulation and performance optimization of a lead-free inorganic perovskite solar cell using SCAPS-1D

Device modeling of high performance and eco-friendly FAMASnI 3 based perovskite solar cell

Structural optimization of inverted CsPbI2Br perovskite solar cells for enhanced performance via SCAPS-1D simulation

Performance optimization of CsPbIBr2-Based Perovskite Solar Cells through Device Modeling

Numerical Simulation of Cs2AgBiBr6-based Perovskite Solar Cell with ZnO Nanorod and P3HT as the Charge Transport Layers

Analysis of Lead Free CsSnBr3 based Perovskite Solar cells utilizing Numerical Modeling

Design and optimization study of all inorganic based double-absorption- layer CsPbI3/MoS 2 heterojunction perovskite solar cells by SCAPS-1D

Enhanced efficiency of bifacial perovskite solar cells using computational study

Optimizing the working mechanism of the CsPbBr3-based inorganic perovskite solar cells for enhanced efficiency

Advanced Optoelectronic Modeling and Optimization of HTL-Free FASnI3/C60 Perovskite Solar Cell Architecture for Superior Performance

Comprehensive performance analysis of perovskite solar cells based on different crystalline structures of MAPbI3

Towards High-Performance Inverted Mesoporous Perovskite Solar Cell by Using Bathocuproine (BCP)

Design and performance exploration of Pb-free low-cost all-inorganic perovskite-inspired CuAgBi2I8 solar cells: Theoretical approach

Optimization of all Pb-free perovskite CsGeI3/FASnI3 tandem solar device with 30.42% efficiency: Numerical simulation using SCAPS