Abstract:Ni-rich NiTi alloys were deposited using the in-situ alloying wire arc additive manufacturing (WAAM) method, with varying deposition currents from 80 A to 120 A. The effects of deposition current on the crystal orientation, precipitation, phase transformation and mechanical properties of the WAAM-deposited NiTi alloys were investigated. The results show that increasing the deposition current during the WAAM process would result in noticeable coarsening of B2 grain and an increased volume fraction of high angle grain boundaries (HAGBs). Also, the texture intensity gradually decreased with increasing deposition current. The fabricated components are dominated by the B2 phase with quantities of Ni4Ti3 precipitates in all samples. When increasing the deposition current during the WAAM process, the size of Ni4Ti3 precipitates generally increased and gradually decomposed into a stable Ni3Ti phase which could be detected in the sample produced at 120 A. Furthermore, all of the characteristic phase transformation temperatures increased with the deposition current while the ultimate tensile strength dropped from 927.9 MPa to 613.8 MPa and elongation reduced from 8.7 % to 5.6 %. The cyclic loading-unloading tests revealed that similar trends for the evolution of irreversible strain (εir), recoverable strain (εre), recovery ratio, and elastic energy storage efficiency (η) during cycling were obtained in all samples processed with different deposition currents. The highest εre of 3.2 % and the highest recovery ratio of 53.9% were obtained in the sample processed with 80 A at an applied stress of 700 MPa for ten cycles. The change of mechanical properties with varying deposition current is due to a combination of factors including precipitation hardening effect, grain refinement effect, and crystal orientation. These results can be useful for optimizing WAAM process parameters to fabricate NiTi components with acceptable structural properties.

Significant Improvement of AISI 1010 Steel Surface Properties by In Situ Nickel-Aluminide Clad Fabricated using Dual Wire Arc Welding

Nickel-aluminide cladding on a steel substrate using dual wire arc additive manufacturing

Fabrication and Characterization of Nickel‐Aluminide Cladding by Dual Wire arc Additive Manufacturing

Surface Cladding of Mild Steel Coated with Ni Containing TiO2 Nanoparticles Using a High-Temperature Arc from TIG Welding

In-situ dual wire arc additive manufacturing of NiTi-coating on Ti6Al4V alloys: Microstructure characterization and mechanical properties

High-efficiency fabrication of Inconel 625 coating for AISI 1045 carbon steel through laser cladding with hot wire: Microstructure and wear resistance

Investigating the Microstructure and Wear Properties of AISI 4140 Steel Clad with WC-Ti Composite Particles Via Gas Tungsten Arc Welding

Improvement in corrosion resistance of wire arc additive manufactured Inconel 625 alloy through heat treatment

Effect of welding parameters on bead characteristics and mechanical properties of wire and arc additive manufactured inconel 718

Cold Metal Transfer-Based Wire Arc Additively Manufactured Austenitic Stainless Steel/Inconel 625/Superduplex Stainless Steel Wall: Microstructural, Corrosion Properties, and Impact Toughness Evaluation

Dry Sliding and Slurry Abrasion Behaviour of Wire Arc Additive Manufacturing - Cold Metal Transfer (WAAM-CMT) Cladded Inconel 625 on EN8 Steel

Microstructure transformation and mechanical behavior in NiTi alloys fabricated by dissimilar double wires arc additive manufacturing

Evolution of crystallographic orientation, precipitation, phase transformation and mechanical properties realized by enhancing deposition current for dual-wire arc additive manufactured Ni-rich NiTi alloy

Wear Behavior Assessment of New Wire-Arc Additively Manufactured Surfaces on AA6061 and AA5086 Alloys through Multi-Walled Carbon Nanotubes and Ni Particles Inducement

Microstructure and mechanical properties of twin wire and arc additive manufactured Ni3Al-based alloy

Effect of Ni addition on the microstructural evolution and lap-shear performance of AISI 630 martensitic stainless steel resistance spot welds

Influence of inconel interlayer on microstructural, mechanical and electrochemical characteristics in single-pass ATIG welding of dissimilar austenitic and duplex stainless steel

Influence of Siliconized Zn-Graphene Oxide Complex Nanoparticles on the Microstructure and Mechanical Properties of AA5083: Focus on Gas Metal Arc Welding

Interface characteristics and mechanical properties of wire-arc depositing Inconel 625 superalloy on ductile cast iron

Effects of welding parameters on Inconel 625 coating synthesised by tungsten inert gas cladding

Investigation of mechanical and microstructure properties of metal inert gas based wire arc additive manufactured Inconel 600 superalloy