Abstract:For resource reutilization, scrap tyres have long been investigated as an additive to concrete to form 'Rubcrete' for various applications and have shown promising results. However, the addition of rubber particles leads to the degradation of physical properties, particularly, the compressive strength of the concrete. In this study, a theoretical model was proposed to shed light on the mechanisms of decrease in compressive strength due to the addition of rubber particles as well as improvement in compressive strength through modification of particle surfaces. The literature suggests that the compressive strength can be improved by soaking the rubber particles in alkaline solution first to increase the inter-phase bonding between the rubber particles and cement. Instead, we discovered that the loss in compressive strength was due to local imperfections in the hydration of cement, induced by the addition of heterogeneous and hydrophobic rubber particles. Microscopic studies showed that the rubber particles disturbed the water transfer to create channels, which were prone to cracking and led to a loss in the compressive strength. Unexpectedly, no cracking was found along the surfaces of the rubber particles, indicating that the bonding strength between the rubber particles and cement phases was not the critical factor in determining the compressive strength. Therefore, a theoretical model was proposed to describe the water transfer in the Rubcrete specimens to explain the experimental data. In the model, the local water available for hydration (Q) is: Q = -A(slv)/6piv, where Q, A(slv), and v are mass flow rate (kg s(-1)), Hamaker constant (J), and dynamic viscosity (m2 s(-1)), respectively. By maximizing the quantity Q and, in turn, the Hamaker constant A(slv), the compressive strength could be improved. The Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that for the hydrated cement particles; the water transfer rate was lower in the presence of rubber particles because the Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that on the hydrated cement particles. Thus, the compressive strength of Rubcrete could be improved by increasing the Hamaker constant of the system. This was achieved by increasing the refractive indices of the solids (n(s)). The refractive indices of materials increase with increases in functional groups, such as OH and SH on the surface. The model provided a possible mechanism for the efficacy of treating rubber particles with NaOH in improving the compressive strength. By using NaOH solution treatment, an oxygen-containing OH group was formed on the rubber surface to increase the Hamaker constant of the system, leading to higher compressive strength. Based on this mechanism, a novel method for modification of the rubber particles was also proposed. In this process, the rubber particles were partially oxidized with hot air/steam in a fluidized bed reactor to produce the hydrophilic groups on the surface of the particles. Preliminary results obtained so far are promising in accordance with the theory.

Thermal conductivity of cement composites containing rubber waste particles: Experimental study and modelling

Thermal Conductivity of Fiber-Reinforced Foam Concrete Filled with Crumb Rubber Powders

Thermal analysis of rubber concrete under the effect of two heat treatments: shock temperature and standard fire

Tailoring the Thermal and Mechanical Properties of Lightweight Cement-Based Composites by Macro and Micro Fillers

Thermal and Mechanical Properties of Concrete Incorporating Silica Fume and Waste Rubber Powder

A multi-scale investigation on recycled ceramic and rubber composite cement-based materials: Acoustic emission, NMR, molecular dynamics simulation

Thermal Insulation Performance Optimization of Hollow Bricks Made up of 3D Printable Rubber-Cement Mortars: Material Properties and FEM-based Modelling

Numerical analysis of the thermomechanical behavior of rubber concrete at high temperatures

Use of waste rubber as concrete additive

Experimental investigation into the properties of crumb rubberized concrete incorporating corrugated round steel fibers

Rubberized mortar: The influence of aggregate granulometry in mechanical resistances and acoustic behavior

Theoretical calculation model for the thermal conductivity of scrap tire rubber–sand mixtures based on soil components

Experimental and numerical investigation on fracture characteristics of self-compacting concrete mixed with waste rubber particles

Effect of Silicone Rubber of a Waste Composite Insulator on Cement Mortar Properties

Properties of Rubberized Engineered Cementitious Composites Containing Nano-Silica

Performance analysis and engineering application of waste rubber crumbs in concrete

Rheological Behaviour of Cementitious Materials Incorporating Solid–Solid Phase Change Materials

Effects of Recycled Rubber Particles Incorporated as Partial Sand Replacement on Fresh and Hardened Properties of Cement-Based Concrete: Mechanical, Microstructural and Life Cycle Analyses

Experimental Investigation and a Predictive Model of the Strength Evolution of Rubberized Cementitious Materials Based on the Virtual Pore Method

The combined effect of carbon fiber and carbon nanotubes on the electrical and self-heating properties of cement composites

Comparison of thermal conductivity and electrical resistivity of carbon-based cementitious composites