Numerical and experimental investigation on dynamic performance of bump foil journal bearing based on journal orbit

ZHOU Yu,SHAO Longtao,Can ZHANG,JI Fenzhu,LIU Jiang,LI Guo,DING Shuiting,Qi ZHANG,DU Farong,Yu ZHOU,Longtao SHAO,Fenzhu JI,Jiang LIU,Guo LI,Shuiting DING,Farong DU

DOI: https://doi.org/10.1016/j.cja.2019.12.001

IF: 5.7

2021-02-01

Chinese Journal of Aeronautics

Abstract:<p>Widespread usage of bump-type foil journal bearing (BFJB) in oil-free micro-turbomachinery requires accurate predictions of dynamic performance characteristics, although it remains a challenging issue because BFJB reflects nonlinear both structurally and aerodynamically. This paper presented a simple experimental method to semi-directly obtain the minimum film thickness and dynamic stiffness of BFJB using the journal orbit. Numerical calculations and simulations are conducted to validate the experimental method. The micro-deformation and interaction of various foils are taken into consideration to improve the model precision. The results from the numerical model regarding the BFJB dynamic characteristics are compared with the experimental results coming from a dedicated test rig, which shows that the experimental results fluctuate obviously and agree not well with the numerical results at the start stage due to the presence of dry friction at that time, nevertheless, they show fantastic agreement as soon as a gas film is gradually generated to separate the shaft from the top foil. Therefore, the proposed experimental method is effective to predict film thickness and dynamic characteristics during the period from the lift-off time to the land-off time. The dynamic characteristics, along with the journal orbits also can be used to rapidly predict the dynamics behavior of rotor-bearing systems.</p>

engineering, aerospace

What problem does this paper attempt to address?

The problem that this paper attempts to solve is about the accurate prediction of the dynamic performance characteristics of **Bump - Foil Journal Bearings (BFJB)**. Although bump - foil journal bearings are widely used in oil - free micro - turbomachinery, due to their structural and aerodynamic nonlinear characteristics, accurately predicting their dynamic performance remains a challenge. This paper proposes a simple experimental method based on the shaft center locus to obtain the minimum film thickness and dynamic stiffness of bump - foil journal bearings in a semi - direct manner, and verifies the effectiveness of this experimental method through numerical calculation and simulation.

### Specific problem description:
1. **Challenges in dynamic performance prediction**: Bump - foil journal bearings exhibit nonlinear characteristics both structurally and aerodynamically, which makes it very difficult to accurately predict their dynamic performance.
2. **Limitations of existing methods**: Current methods usually require a large amount of time - domain data and perform Fourier transform to obtain frequency - domain data, which results in high computational cost and complex testing.
3. **Innovation of the experimental method**: This paper proposes an experimental method based on the shaft center locus, which can directly measure the minimum film thickness and dynamic stiffness of bump - foil journal bearings, thereby simplifying the experimental process and improving the prediction accuracy.

### Solutions:
1. **Experimental method**: A new bump - foil journal bearing test rig was designed, and the shaft center locus was measured by displacement sensors installed on both sides of the bearing, and then the minimum film thickness and dynamic stiffness were predicted.
2. **Numerical model**: A two - dimensional shell element model considering the micro - deformation and interaction of foils was established, and the dynamic gas - lubricated Reynolds equation was solved using the finite difference method to obtain the dynamic stiffness and dynamic damping coefficients.
3. **Verification method**: The effectiveness of the proposed experimental method was verified by comparing the experimental results with the numerical simulation results.

### Key formulas:
- **Dimensionless compressible gas - lubricated Reynolds equation**:
\[
\frac{\partial}{\partial \eta}\left(\frac{h}{C_{0}}^{3}\frac{\partial p}{\partial \eta}\right)+\frac{\partial}{\partial \zeta}\left(\frac{h}{C_{0}}^{3}\frac{\partial p}{\partial \zeta}\right)=K\left(\frac{\partial}{\partial \eta}\left(\frac{h}{C_{0}}\frac{\partial p}{\partial t}\right)+2K\frac{\partial}{\partial t}\left(\frac{h}{C_{0}}\frac{\partial p}{\partial t}\right)\right)
\]
where:
- \(p\) is the dimensionless pressure
- \(h\) is the dimensionless film thickness
- \(\eta\) and \(\zeta\) are the dimensionless coordinates
- \(t\) is the dimensionless time
- \(K\) is the dimensionless constant

- **Dynamic stiffness and damping coefficients**:
\[
K_{xx}, K_{xy}, K_{yx}, K_{yy}, C_{xx}, C_{xy}, C_{yx}, C_{yy}
\]
These coefficients can be obtained from the perturbed pressure by the partial derivative method.

### Conclusion:
In this paper, through a combination of experimental and numerical simulation methods, a method for predicting the dynamic performance of bump - foil journal bearings based on the shaft center locus was successfully proposed, providing an effective means for rapidly predicting the dynamic behavior of rotor - bearing systems.