Abstract:High-energy-density batteries are actively sought after for next-generation electric vehicle (EV) applications, triggering the search for sulfur-based positive electrode materials with high capacity for extended driving range. One of the primary issues of sulfur cathodes is the rapid capacity decay caused by the dissolution of sulfur in the electrolyte and the resulting parasitic reactions. This can be prevented by incorporating a suitable amount of carbon material into the sulfur electrodes, because of its inherent properties; however, introducing a large amount of low-density carbon materials will lead to a decrease in the energy density of the battery. Therefore, an alternative method to suppress sulfur dissolution is required for commercial applications. Recently, we developed a Fe-containing Li2S-based material (Li8FeS5) as the sulfur cathode; it has a relatively high initial discharge capacity (>700 mAh·g−1) and electric conductivity. However, rapid capacity degradation was observed during the initial several cycles, due to some unknown reactions between the electrolyte and Li8FeS5. In this study we demonstrate an effective method to improve the cycle performance of Li8FeS5 by coating its surface with a stabilizing material. We selected titanium oxide as the coating material, based on its high stability toward liquid electrolytes and its strong interaction with sulfur. Hence, we obtained TiOx-coated Li8FeS5 particles (Li8FeS5-TiOx) by a liquid-phase reaction. The transmission electron microscopy observation revealed that the Li8FeS5 particles were coated with several tens of nanometers of TiOx layers. The Li8FeS5-TiOx cells exhibited improved cycling performance with a carbonate electrolyte. We also observed that the capacity originating from an iron redox was not affected by coating during the cycling test; in contrast, the degradation of the cell capacity corresponding to the sulfur redox was suppressed significantly after coating with the TiOx layer. Thus, the surface reaction of Li8FeS5 with the electrolyte, which could be the main reason for the cycling degradation, was effectively suppressed by coating with the TiOx layer.

Improving surface activity of TiO2 by introducing Co sources to enhance its ability to capture polysulfides

Regulating positions of TiO2 on TiO2/biomass carbon composite surface to enhance conversion abilities of polysulfides

A thick titanium dioxide layer formed by Co-doping on a carbon surface promotes the polysulfide-adsorption ability in Li–S batteries

TiO2 as a multifunction coating layer to enhance the electrochemical performance of SiOx@TiO2@C composite as anode material

Tailoring Surface Acidity of Metal Oxide for Better Polysulfide Entrapment in Li‐S Batteries

Interfacial-engineered Cobalt@carbon Hybrids for Synergistically Boosted Evolution of Sulfate Radicals Toward Green Oxidation

Enhancing Catalytic Activity of Titanium Oxide in Lithium–Sulfur Batteries by Band Engineering

Intrinsic catalytic Sites-Rich Co-doped SnO2 nanoparticles enabling enhanced conversion and capture of polysulfides

Insight into the boosted activity of TiO 2 -CoP composites for hydrogen evolution reaction: Accelerated mass transfer, optimized interfacial water, and promoted intrinsic activity

A Hierarchically Porous TiO2@C Membrane with Oxygen Vacancies: a Novel Platform for Enhancing the Catalytic Conversion of Polysulfides.

The catalytic role of surface Co(PO3)2 on CoP for high-performance lithium-sulfur batteries

Boosting cation desorption, anion adsorption and surface redox reaction kinetics of Co3O4 by oxygen vacancy

Improvement of Cycling Capability of Li2S-FeS Composite Positive Electrode Materials by Surface Coating With Titanium Oxide

Synergistic effect of atomically dispersed Cu species and Ti-defects for boosting photocatalytic CO2 reduction over hierarchical TiO2

Oxidation States Regulation of Cobalt Active Sites through Crystal Surface Engineering for Enhanced Polysulfide Conversion in Lithium–Sulfur Batteries

Manipulating the Conversion Kinetics of Polysulfides by Engineering Oxygen p‐Band of Halloysite for Improved Li‐S Batteries

Heterostructuring Cobalt Sulfide with Highly Oxophilic 1T-Tungsten Sulfide for Durable and Efficient Oxygen Electrocatalysis

Bifunctional Electrocatalyst of Low-Symmetry Mesoporous Titanium Dioxide Modified with Cobalt Oxide for Oxygen Evolution and Reduction Reactions

Sulfurization-Assisted Cobalt Deposition on Sm2Ti2S2O5 Photocatalyst for Water Oxidation under Visible Light Irradiation

Surface Modification of Y<sub>2</sub>Ti<sub>2</sub>O<sub>5</sub>S<sub>2</sub> with Co<sub>3</sub>O<sub>4</sub> Co-catalyst for Photocatalytic Oxygen Evolution

Enhancement Effects of Cobalt Phosphate Modification on Activity for Photoelectrochemical Water Oxidation of TiO2 and Mechanism Insights.