Abstract:The properties of lightweight, high strength, better corrosion resistance, high electrical conductivity, etc. made aluminium alloys one of the favorite materials for industrial purposes. The aerospace, marine, automobile and railway industries use these alloys very commonly. But the lower melting temperature, high thermal conductivity and unusual grain growth make it difficult to weld material. So solid-state welding process named friction stir welding (FSW) is used for higher welding joint efficiencies for these alloys. The performance of FSWed joints directly depends upon the levels of input parameters used for the welding process. The present study is an attempt to optimize the process parameters for FSW of armor-grade aluminium alloys AA5083. Tool design parameters (Shoulder Diameter, Shoulder Flatness and Pin Profile) along with machine parameters (welding speed) are used for variation to analyze their effects on the quality of the joints. The experiments were designed by the response surface methodology and the significance of these parameters was analyzed by ANOVA. Where all four considered parameters were found significantly affect the responses i.e. ultimate tensile strength, yield tensile strength and elongation. An optimized set of parameters was revealed by Desirability a multi-objective optimization approach. “Desirability” suggests 18.5 mm shoulder diameter, 2.0 mm shoulder flatness, square pin profile and 48.9 mm/min welding speed as a set of optimized parameters. The 77.9% joint efficiency can be achieved at the mentioned optimized parameters. To analyze the relationships between variation in responses with the variation in process parameters and the microstructure of the welded joints the microstructure analysis has been conducted. The microstructural analysis revealed that high heat input causes an unwanted grain growth in the heat-affected zone and the lower heat input causes an insufficient temperature for the softening of the material in the nugget zone.

Optimization of FSW Parameters Using SA Algorithm and ANFIS-Based Models to Maximize Mechanical Properties of AZ80A Mg Alloy Joints

Experimental And Optimization-Based Analysis To Maximize Mechanical-Related Attributes Of Friction Stir Welded Cda101 Cu Alloy Joints

Generation of regression models and multi-response optimization of friction stir welding technique parameters during the fabrication of AZ80A Mg alloy joints

ANN modeling and optimization of friction stir welding performance for AA6061 and AA5083 alloy joints

Multi-objective optimization of FSW variables on joint properties of AA5754 aluminum alloy using Taguchi approach and grey relational analysis

Multi-objective optimization of FSW process parameters for AA1100 joints by using a hybrid technique of PCA-TOPSIS

Experimental investigation and parametric optimization of FSW of mineral-reinforced AA6061 matrix composite

Mathematical modeling and optimization of friction stir welding process parameters for armor-grade aluminium alloy

Modeling and optimization of tool parameters in friction stir lap joining of aluminum using RSM and NSGA II

A multi-objective optimization using response surface model coupled with particle swarm algorithm on FSW process parameters

Identifying the optimal FSW process parameters for maximizing the tensile strength of friction stir welded AISI 316L butt joints

Response surface, neural network, and experimental approach to optimize process parameters and characterization of Al-Mg alloy by friction stir welding

Multi-response optimization of FSW process parameters of dissimilar aluminum alloys of AA2014 and AA6061 by response surface methodology (RSM)

Investigations and optimization of friction stir welding process to improve microstructures of aluminum alloys

Multiobjective Optimization of Friction Stir Welding Process Parameters on Aluminum Alloy AA 5083 Using Taguchi-Based Grey Relation Analysis

An experimental study and parameter optimization of FSW for welding dissimilar 6061 and 7075 Al alloys

Investigation on the influence of FSP parameters on TIG welded dissimilar aluminum joints using RSM and desirability function approach

Optimization of process parameters of aluminum alloy AA 2014-T6 friction stir welds by response surface methodology

Multi-objective Optimization of FSW Process Parameters of Aluminium Alloy Using Taguchi-Based Grey Relational Analysis

Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy

Optimization of the Welding Parameters of High-Quality Aluminum/Copper FSSW Joints Using Taguchi Method Combined with Back Propagation Neural Network and Genetic Algorithm