Abstract:<p>A co-precipitation hardened medium-Mn steel with respective NiAl and Cu-rich particles in dual phases (austenite and ferrite) has been designed by using a quenching-partitioning-tempering (QPT) treatment. The influences of co-precipitates on the elasto-plastic transition and strain compatibility has been investigated based on the micro-mechanical behavior of constituent phases, the evolution of lattice strain and stress components. Compared to the Cu-Free steel, in which single NiAl precipitates form in ferrite, co-precipitation in the Cu-Added steel results in an improved strain compatibility between austenite (γ) and ferrite (α). The lattice strains of both γ and α phases show similar evolutions during the entire strain regime, and a homogeneous elasto-plastic deformation occurs together with a continuous yielding and weak transient of strain hardening rate. The improved strain compatibility leads to an alleviation of strain localization in the phase interfaces, so that the overall back stress increases slowly with the tensile strain increasing during the whole plastic deformation process, although the transformation-induced plasticity (TRIP) effect of the Cu-Added steel only occurs at low strains (<5%) due to the low mechanical stability of the retained austenite. In contrast, a non-continuous yielding of the constituent phases occurs in the Cu-Free steel leads to strong strain transfer across the α/γ interfaces due to a low deformation compatibility between austenite and ferrite. High internal stress in the phase interfaces results in easy damage-crack formation, but it can be accommodated by the TRIP effect which dominates in large strains, resulting in back stress decreasing and effective stress hardening during the subsequent deformation stage. However, the introduction of hydrogen can aggravate the dislocation accumulation and strain transfer between austenite and ferrite; thus, hydrogen-induced cracks (HICs) are prone to nucleate at the α/γ interfaces while the TRIP effect is not significant, leading to premature failure and significant elongation loss (85.4%) of the Cu-Free steel. Therefore, the improved strain compatibility of the Cu-Added steel contributes to a better resistance to hydrogen embrittlement, although both medium Mn steels possess similar tensile strength (1 GPa) and elongation (25%) values.</p>

Improved resistance to hydrogen embrittlement in the nugget zone of friction stir welded medium Mn steel via post-welding annealing

Hydrogen embrittlement behavior in the nugget zone of friction stir welded X100 pipeline steel

Interactions of Nanoprecipitates, Metastable Austenite, and Lüders Banding in an Ultra-Low Carbon Medium Mn Steel with Abnormal Strength Dependence of Hydrogen Embrittlement

Effect of Intercritical Annealing Time on Hydrogen Embrittlement of Warm-Rolled Medium Mn Steel

Hydrogen embrittlement behavior of high strength low carbon medium manganese steel under different heat treatments

Hydrogen embrittlement and hydrogen diffusion behavior in interstitial nitrogen-alloyed austenitic steel

Experimental Investigation of the Effect of Hydrogen on Fracture Toughness of 2.25Cr-1Mo-0.25v Steel and Welds after Annealing

The potential significance of tempering treatment in alleviating the hydrogen embrittlement susceptibility of a hot-rolled and intercritically annealed medium-Mn steel

Dependence of hydrogen embrittlement on annealing time in medium-Mn steels

In-depth Understanding in the Effect of Hydrogen on Microstructural Evolution, Mechanical Properties and Fracture Micro-Mechanisms of Advanced High-Strength Steels Welded Joints

Homogeneous elasto-plastic deformation and improved strain compatibility between austenite and ferrite in a co-precipitation hardened medium Mn steel with enhanced hydrogen embrittlement resistance

Improvement of Resistance to Hydrogen Embrittlement for 1300MPa Ultra-high Strength Steel by Introducing Nano-sized Cu-rich Phase Precipitation

Hydrogen Embrittlement of Austenitic Stainless Steels at Low Temperatures

Optimization of the hydrogen embrittlement resistance in ultra-high-strength multi-alloyed steel via controlling the reversed austenite fraction and stability

Effect of Retained Austenite on the Hydrogen Embrittlement of a Medium Carbon Quenching and Partitioning Steel with Refined Microstructure

Mechanical Strengthening and Corrosion Behavior of Friction Stir Welded Dual-Phase Fe50Mn30Co10Cr10 High Entropy Alloy

Optimizing the hydrogen embrittlement resistance by Cu addition in a low carbon high strength steel

Change in Hydrogen Trapping Characteristics and Influence on Hydrogen Embrittlement Sensitivity in a Medium-Carbon, High-Strength Steel: The Effects of Heat Treatments

Hydrogen-assisted decohesion associated with nanosized grain boundary κ-carbides in a high-Mn lightweight steel

Hydrogen-enhanced microbanding in an austenitic FeMnAlC low-density steel: Effect on hydrogen embrittlement resistance

The role of reverted transformation in hydrogen embrittlement of a Cu-containing low carbon high strength steel