Abstract:ARGO-YBJ ia a detector optimized to study small size air showers. It consists of a layer of Resistive Plate counters (RPCs) covering an area of about 6500 m^2 and will be located in the Yangbajing Laboratory (Tibet, China) at 4300 m above the sea level. ARGO-YBJ will be devoted to a wide range of fundamental issues in cosmic rays and astroparticle physics, including in particular gamma-ray astronomy and gamma-ray bursts physics in the range 10 GeV-500 TeV. The sensitivity of ARGO-YBJ to detect high energy GRBs is presented.
What problem does this paper attempt to address?
The problem that this paper attempts to solve is: **To study the variation law of fracture toughness of the enhanced polymer interface with the degree of polymerization \(N\) of the connecting chains during the chain pull - out process**.
Specifically, the authors focus on the fracture behavior of polymer interfaces enhanced by diblock copolymers under different modes (tensile mode and shear mode). Through molecular dynamics simulations, they explore the influence of the length of the connecting chains on the fracture toughness of the interface and propose a scaling theory to explain the different dependencies in the cases of short and long chains.
### Main problem decomposition:
1. **Background and motivation**:
- Polymer mixtures usually form macroscopically phase - separated structures, resulting in weak adhesion at the interface, which limits the overall performance of the material.
- In order to strengthen these weak interfaces, diblock copolymers are usually added. These copolymers can form bridges on the interface and improve the fracture toughness of the interface.
2. **Research objectives**:
- To explore the influence of the degree of polymerization \(N\) of the connecting chains on the fracture toughness of the enhanced polymer interface.
- To study the differences in fracture toughness under different modes (tensile and shear).
- To propose a scaling theory that can explain the different dependencies of fracture toughness in the cases of short and long chains.
3. **Methods**:
- Use Brownian dynamics simulation to study the process of a single connecting chain being pulled out from a two - dimensional semi - infinite barrier matrix.
- Quantify the fracture toughness of the interface by calculating the work \(G\) required to pull out the chain.
- Analyze the variation law of fracture toughness under different chain lengths \(N\).
4. **Main findings**:
- For short chains (\(N\leq100\)), the fracture toughness \(G\) increases linearly with the degree of polymerization \(N\), that is, \(G\sim N\).
- For long chains (\(N > 100\)), the fracture toughness \(G\) increases at a faster rate with the degree of polymerization \(N\), following the relationship \(G\sim N^{3/2}\).
- The fracture toughness in the tensile mode is about five times higher than that in the shear mode.
5. **Theoretical explanation**:
- For short chains, the connecting chains mainly interact with the barrier layer near the interface, so the fracture toughness increases linearly.
- For long chains, the connecting chains can penetrate deeper into the interface, and more chain segments participate in the movement, resulting in the fracture toughness increasing at a rate of \(N^{3/2}\).
### Formula summary:
- Relationship between fracture toughness and degree of polymerization:
\[
G \sim
\begin{cases}
N & \text{for short chains} \\
N^{3/2} & \text{for long chains}
\end{cases}
\]
- Lagrange equation describing chain segment motion:
\[
\nu \left( \frac{d\mathbf{r}_i}{dt} - \mathbf{v}_0 \right) = \tau_i (\mathbf{r}_{i+1} - \mathbf{r}_i) - \tau_{i-1} (\mathbf{r}_i - \mathbf{r}_{i-1}) + F_i + \eta_i
\]
where:
- \( \nu \) is the viscous friction coefficient,
- \( \mathbf{v}_0 \) is the constant tensile speed,
- \( \tau_i \) is the tension of the \(i\) - th chain segment,
- \( F_i \) is the short - range repulsive force,
- \( \eta_i \) is the Gaussian random noise.
Through these studies, the authors reveal the important influence of the length of the connecting chains on the fracture toughness of the enhanced polymer interface and provide a theoretical basis for designing composite materials with higher fracture toughness.