Abstract:An isolated single polymer suspending in the dilute solution exhibits a collapse transition when switched from good solvent to poor solvent. The transition passes through a thermally reversible intermediate molten globule state holding a characteristic core-shell structure with a concentrated core and a dilute shell, which appears more obvious for shorter chains. Therefore, the collapse transitions of short-chain polymers appear more gradual than those of long-chain polymers. This intermediate molten globule state is interesting because it allows a better understanding of the protein folding and its bio-functions as well as of polymer interface properties. We performed dynamic Monte Carlo simulations to compare the intermediate molten globule state of a single ring polymer to that of a single linear polymer. Their molten globule structures appeared very similar. This observation thus ruled out the specific effect of chain ends, and allowed us to focus on the surface effect of the globules in the intermediate states, which was also obvious for the limited chain length. We observed that, right below the theta point as the critical demixing point for solution of the polymer with infinite chain lengths, the intermediate molten globule states showed two energy states of monomers separately in the core and in the shell, appearing as a coexistence of two concentrations separately deviating from the critical. point. We, therefore, considered the molten globule state as a result of pre-dissolution, similar to the pre-melting phenomenon of single-chain single crystals around their equilibrium melting points. The surface dissolution model was then applied to describe the characteristic core-shell structures near the critical point during collapse transition of single-chain polymers. According to the surface dissolution model, near the critical theta point, the globule-solvent interface energy of the collapsed globules became high, which was then optimized by forming a thin layer of coexisting dilute phase, i.e. replaced by the globule-coil plus coil-solvent interface energy. The situation is something similar to the complete wetting of the vapour on a solid substrate, except that the partial surface dissolution achieves a minimum free energy with an equilibrium thickness of the surface layer. In fact, on the phase diagram, right below the theta point, any concentration deviation from the theta state will enter the metastable region for first-order phase transition. The equilibrium layer thickness defines the soluble length of chain segments on the surface. For a real single-chain polymer, however, the extent of surface dissolution may not be able to reach the equilibrium end, because the topological constraint inside the globule, for example, a knotting, will not allow the equilibrium lengths of chain segments to release at the globule surface. This kind of pre-dissolution behaviours could be unique for polymers at interfaces near the critical point. Since shorter chains make smaller globules, their surface dissolution phenomena become more obvious and their collapse transitions appear more gradual. Owing to the surface dissolution near the critical point for phase separation, the distribution of monomer energy states becomes discontinuous along the direction normal to interface. This behaviour reveals a discrepancy at the molecular level if compared to the traditional theoretical treatment of a continuous concentration gradient along this normal direction for the critical interfaces. Thus, the pre-dissolution model may provide a profound approach to better understand the microscopic nature of polymers at the near-critical fluid-fluid interfaces.

Self-organising Dissipative Polymer Structures

The Phase Behavior Of Polyethylene Ring Chains

Polymer Thin Film Necking: Ductility from Entanglements and Plane Stress Condition

Mesoscopic Dynamics Of Inhomogeneous Polymers Based On Variable Cell Shape Dynamic Self-Consistent Field Theory

Intermediate Molten Globule State and Its Thermodynamic Interpretation in the Collapse Transition of Single Ring Polymer

Non-Rouse behavior of short ring polymers in melts by molecular dynamics simulations

The Chain Stretching Effect on the Morphology and Rheological Properties of Phase‐Separating Polymer Blends Subjected to Simple Shear Flow

Static and dynamic scaling behavior of a polymer melt model with triple-well bending potential

Dynamics of Polymer Chains in Disperse Melts: Insights from Coarse-Grained Molecular Dynamics Simulations

Dynamics in polymers with phase separated dynamic bonds: the case of a peculiar temperature dependence

Unraveling the glass-like dynamic heterogeneity in ring polymer melts: From semi-flexible to stiff chain

Molecular Simulations Revealing Effects of Non-concatenated Ring Topology on Phase Behavior of Symmetric Diblock Copolymers

Self-Similar Conformations and Dynamics in Entangled Melts and Solutions of Nonconcatenated Ring Polymers

Multi-scale entropic depletion phenomena in polymer liquids

Dynamics and Rheology of Polymer Melts via Hierarchical Atomistic, Coarse-grained, and Slip-spring Simulations

Conformation and Structure of Ring Polymers in Semidilute Solutions: A Molecular Dynamics Simulation Study

Brush-Like Polymers and Entanglements: from Linear Chains to Filaments.

Effect of Dispersity on Dynamic Properties of Polymer Melts: Insights from Coarse-Grained Molecular Dynamics Simulations

Structural Rheology in the Development and Study of Complex Polymer Materials

Molecular Mobility in the Amorphous Phase Determines the Critical Strain of Fibrillation in the Tensile Stretching of Polyethylene

Rationally Leveraging Polymer Chain-Length Heterogeneity for Robust Structural Engineering