Abstract:It is highly desired to efficiently dissipate the high heat flux generated in electronics. A novel hybrid microchannel heat sink combining manifold with secondary oblique channels (MMC-SOC) has been proposed and studied numerically in our previous work. The current study conducts the fabrication and experimental test of the hybrid microchannel heat sink using dielectric fluid HFE-7100. The volume flow rate qv ranges from 211 to 580 mL/min, with channel Reynolds numbers between 278 and 905 for heat fluxes q'' = 20, 25, 30 and 35 W/cm2. The results indicate that the MMC-SOC heat sink can simultaneously reduce the thermal resistance Rt and pressure drop ∆P. For heat sinks with channel height Hc = 60 μm, an 11% reduction in ∆P and a 24% reduction in Rt are obtained compared to conventional manifold microchannel (MMC) heat sink for qv = 580 mL/min and q'' = 20 W/cm2. As qv increases, the ratio (Rt/Rt0) becomes smaller and (∆P/∆P0) becomes larger, which indicates an enhanced ability of reducing Rt and a suppressed ability of reducing ∆P. For the maximum qv = 580 mL/min and q'' = 35 W/cm2, the MMC-SOC heat sink can maintain a maximum chip temperature of 53 °C with a pressure drop of only 3.77 kPa. Moreover, the proposed MMC-SOC heat sink has a lower pressure drop compared to MMC heat sink owing to a reasonable design, even though the Reynolds number of the MMC-SOC heat sink reaches up to 883. This provides a very promising scheme for safe and efficient single-phase microchannel cooling used in the thermal management of electronics with high heat flux. In addition, the ratio (Rt/Rt0) will increase with increasing heat flux and increasing the flow rate becomes an effective way to further reduce the chip surface temperature at operating conditions with higher heat flux.

Investigation of a hybrid two-layered channel-jet heat sink for air cooling

An Experimental Study of Microchannel and Micro-Pin-Fin Based On-Chip Cooling Systems with Silicon-to-Silicon Direct Bonding.

Experimental Study on Cooling Performance of a Hybrid Microchannel and Jet Impingement Heat Sink

Jet Microchannel with Sawtooth Wall for Efficient Cooling of High-Power Electronics

Heat Dissipation Characteristics of a Jetting Staggered Microchannel for Cooling a Large-area High-performance SOC Chip

Efficient Thermal Management of High-Power Electronics Via Jet-Enhanced HU-type Manifold Microchannel

Characteristics analysis and structure optimization of a hybrid micro-jet impingement/micro-channel heat sink

Numerical Investigations of Heat Transfer in Hybrid Microchannel Heat Sink with Multi-Jet Impinging and Trapezoidal Fins

Numerical Study on Heat Transfer Efficiency and Inter-Layer Stress of Microchannel Heat Sinks with Different Geometries

Hybrid Mini/Micro-Channel Heat Sink Using Liquid Metal and Water As Coolants

Numerical Study of Laminar Heat Transfer and Pressure Drop Characteristics in A Water-Cooled Minichannel Heat Sink

Numerical Study on Hybrid Discontinuous Microchannel Heat Sink Combining Manifold with Pin Fins (DMC-MPF) for High Power Electronic Device

Thermal Performance of the Multilayered Honeycomb Microchannel Heat Sink

A Kind of Microchannel Heat Sink Optimization for High Power Chips Based on Cfd and Non-Silicon Mems Technology

Design of Microchannel Heat Sink Using Topology Optimization for High Power Modules Cooling

Co-Design of Intermittent Jet and Surface Structure for Heat Sink Cooling Enhancement

Embedded microfluidic cooling with compact double H type manifold microchannels for large-area high-power chips

HEAT TRANSFER ENHANCEMENT OF A NEW SINGLE-PHASE HYBRID COOLING SCHEME OF MICROCHANNEL AND MICROJET IMPINGEMENT

Experimental study on single-phase hybrid microchannel cooling using HFE-7100 for liquid-cooled chips

Thermal-hydraulic Performance of Microchamber Heat Sinks with Run-Through Metal Pillar Arrays and Hot-Spot Oriented Manifold Inlets

Assessment of cooling performance of mini/micro-channel stacked double layer heat sink