Abstract:For patients with mandibular bone defects, although reconstruction plates can be used for repair, achieving both occlusal function and facial aesthetics is challenging. In the present study, in vitro experiments and finite element analysis (FEA) were conducted to determine the biomechanical characteristics of multiple porous lattice structures of varying shapes and diameters that were used for mandibular implants. Additionally, an abutment designed to carry occlusal forces was added to the tops of the implants. The stress distribution of four lattice designs (Tetrahedron, Quad-diametral-cross, Hex-star, and Hex-vase) of three sizes (2.5, 3.0, and 3.5 mm) in cubic porous models were analysed by FEA. Subsequently, two optimal designs for 3D-printed titanium alloy were selected. These designs, featuring different lattice diameters (0.5, 0.7, and 0.9 mm), were tested to determine their elastic modulus. These elastic modulus were used in another FEA of a mandibular implant designed for a patient with a malignant tumor in the right mandible. This model, which included an abutment design, was subjected to a vertical force of 100 N and muscle forces generated by biting. This analysis was conducted to determine the elastic modulus of the implant and the values of stress and strain on the implant and surrounding bone. The lattice designs of Quad-diametral-cross and Hex-vase exhibited smaller high-stress regions than those of Tetrahedron and Hex-star did. In vitro tests revealed that the elastic modulus of the lattices increased with the rod diameter. When these values were applied in mandibular implants, Young’s modulus decreased, which in turn increased the frictional stress observed at the interface between the abutment and the implant. However, the implant’s maximum stress remained below its yield strength (910 MPa), and the strain on the surrounding bone varied between 1500 and 3000 µstrain. As indicated by Frost’s theory, these implants are unlikely to damage the surrounding bone tissue and are likely to support bone growth. In conclusion, the lattice designs of Quad-diametral-cross and Hex-vase have small high-stress regions for mandibular implants. Increasing the diameter of the lattice rods increases Young’s modulus, which in turn reduces the frictional stress between the abutment and the implant. Even when the highest Young’s modulus is reached, the stress on the implant remains below its yield strength, and the bone strain remains within the range of 1500 to 3000 µstrain.

Flexural mechanical properties of Ti-6Al-4V multilayer micro-lattice biomaterials for skull repair

Quasi-static compressive mechanical properties of multilayer micro-lattice biomaterials for skull repair

The performance tests of three-dimensional printing titanium alloy craniomaxillofacial bone plate: A preliminary preclinical study

Computational biomechanical analysis of Ti-6Al-4V porous bone plates for lower limb fractures

Microstructure and Mechanical Properties of Ti-Al-Ti-Ti2AlNb Laminated Composites Based on the Ductile-brittle Structure

Study on mechanical properties of dual-channel cryogenic 3D printing scaffold for mandibular defect repair

Cyclic flexural fatigue of porous Ti6Al4V constructs for use in mandibular reconstruction

Fingers crossed: Biomechanical analysis of partial mandibular implant with various level of material properties by different shapes, sizes, and rod diameter of lattice designs: In-vitro experiment and finite element simulation

Biomechanical Study on the Comparison of Synthetic Materials for Cranio-Orbital Fracture Repair

Microstructural features and compressive properties of SLM Ti6Al4V lattice structures

Lattice Ti Structures with Low Rigidity but Compatible Mechanical Strength: Design of Implant Materials for Trabecular Bone

Compressive properties of Ti6Al4V Functionally Graded Lattice Structures via topology optimization design and selective laser melting fabrication

Bioactive Zn-0.6Cu thin sheet for craniofacial bone repair: In vitro and in vivo evaluations

Effect of heat treatment on mechanical properties, failure modes and energy absorption characteristics of lattice skeleton and sheet structures fabricated by SLM

Design and performance evaluation of additively manufactured composite lattice structures of commercially pure Ti (CP–Ti)

A high-strength mineralized collagen bone scaffold for large-sized cranial bone defect repair in sheep

Bionic mechanical design and 3D printing of novel porous Ti6Al4V implants for biomedical applications

Compressive properties and deformation mechanism of selective laser melting of Ti6Al4V porous femoral implants based on topological optimization

Compressive properties and biocompatibility of additively manufactured lattice structures by using bioactive materials

Design and mechanical testing of porous lattice structure with independent adjustment of pore size and porosity for bone implant

Fracture Mechanics of Bi-material Lattice Metamaterials