Abstract:The high cracking susceptibility is the major barrier hindering the broad adoption of additive manufacturing (AM) in traditional non-weldable superalloys. It is particularly important to explore the role of elements during the AM processing and establish a new alloy design criterion. In this study, the effect of carbon, a critical element that influences the solidification and mechanical properties of superalloys, on the printability and mechanical properties of a typical non-weldable Inconel 738 (IN738) alloy processed by laser powder bed fusion (LPBF) was studied. Different from the limitation of low carbon content in traditional superalloy design, it was found that a moderate increase of carbon content from 0.11 wt% (alloy IN738LC) to 0.3 wt% (alloy IN738-0.3 C) and 0.6 wt % (alloy IN738-0.6 C) can produce crack-free LPBF samples in a wide range of processing parameters. The effect of carbon content on the microstructure, tensile properties and cracking susceptibility of the LPBF-printed alloys was evaluated. With the increase of carbon content, more granular monocarbides of no more than 200 nm in size form into a quasi-continuous or continuous network at the boundaries of cellular structures, while the low melting-point phases containing boron and gamma/gamma ' eutectics at cellular boundaries are significantly reduced. The susceptibility to solidification cracking and liquation cracking is substantially decreased owing to the reduced level of element segregation, elimination of initiation source for liquid films, and decrease of local strain con-centration. As a result, LPBF IN738-0.3 C and IN738-0.6 C show excellent ultimate tensile strength (1320 and 1598 MPa) and superior total elongation (14.7% and 9.0%), respectively. The results above demonstrate the different roles of carbon element in AM and the potential for designing AM non-weldable superalloys with improved printability and mechanical properties via alloy composition optimization.

The effect of carbon content on the printability and mechanical properties of Ni-based superalloy in laser additive manufacturing

Effect of C content on the microstructures and mechanical properties of laser additive manufactured Ni-base superalloys

Effect of Carbon Content on the Microstructure, Tensile Properties and Cracking Susceptibility of IN738 Superalloy Processed by Laser Powder Bed Fusion

The Enhancement Effect of Carbides on the Printability and Mechanical Properties of a Ni–Fe–Cr–Al–Ti Alloy Processed by Electron Beam Freeform Fabrication

Effect of carbon addition on microstructure and mechanical properties of a typical hard-to-deform Ni-base superalloy

Effects of Co and Nb on the Crack of Additive Manufacturing Nickel-Based Superalloys

Study on Crack Behavior of GH3230 Superalloy Fabricated via High-Throughput Additive Manufacturing

On the influence of alloy composition on the additive manufacturability of Ni-based superalloys

Phase constitution, microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing

Carbon addition and temperature dependent tensile deformation resistance and capacity of a low-cost 3rd-generation Ni-based single crystal superalloy

Influence of Cr/Mo ratio on microstructure and mechanical properties of the Ni-based superalloys fabricated by laser additive manufacturing

Effect of carbon on the solidification microstructure of single crystal Ni-based superalloy AM3

Effect of C Content on Microstructure and Hot Deformation Behavior of a Ni-based Superalloy

Influence of Co Content on the Microstructures and Mechanical Properties of a Ni–Co Base Superalloy Made by Specific Additive Manufacturing Process

Precipitation, Transformation, and Coarsening of Carbides in a High-Carbon Ni-based Superalloy During Selective Laser Melting and Hot Isostatic Pressing Processes

Effect of Fe and C Contents on the Microstructure and High-Temperature Mechanical Properties of IN625 Alloy Processed by Laser Powder Bed Fusion

The influence of additive manufacturing on Portevin-Le Châtelier (PLC) effect in Ni-Co-based superalloy

Effect of Heat Treatment on Microstructure and Mechanical Properties of a Selective Laser Melting Processed Ni-Based Superalloy GTD222

The Effects of Co on the Microstructure and Mechanical Properties of Ni-Based Superalloys Prepared via Selective Laser Melting

Research status on the effect of energy density on the forming microstructure and properties of nickel-based superalloys for laser additive manufacturing

Crack Inhibition and Performance Modification of NiCoCr-Based Superalloy with Y2O3 Nanoparticles by Laser Metal Deposition