Abstract:It is a well-known fact that the consumption of conventional cutting fluids in metalworking industries leads to severe health and environmental issues. Owing to the EPA (Environmental Protection Agency) increasing regulations regarding pollution and contamination, there is a dire need for a greener fluid with excellent cooling and lubrication characteristics to diminish the environmental impact of cutting fluids, as well as to improve machinability. Cryogens are greener and excellent coolants but poor lubricants, while ester oils are excellent lubricants and poor coolants. Therefore, a hybrid lubri-coolant cutting fluid with synergistic cooling and lubrication characteristics could be a desideratum to replace conventional cutting fluid. To investigate a newly proposed hybrid lubri-coolant, thermophysical properties (density, thermal conductivity, specific heat, and viscosity), heat transfer properties (surface temperature, heat flux, and heat transfer coefficient), and machinability properties (tool life, etc.) are key characteristics of the fluids that decide phase change and heat dissipation capabilities during their application in machining. In the current experimental study, hybrid ethanol–ester oils with/without dry ice (−78 °C) are proposed as cutting fluids and holistically investigated in terms of thermo-physical properties, heat transfer properties, and machinability properties under different cutting conditions. Experimental findings have depicted a 20%, 10%, and 5% decrease in density, specific heat, and viscosity, respectively, with a 15% increase in the thermal conductivity of the fluid with the addition of dry ice. The dry-ice-based hybrid lubri-coolant sprayed onto a Ti-6Al-4V plate enhanced the heat transfer coefficient significantly by 17% compared to hybrid lubri-coolant without dry ice. Besides, hybrid ethanol–ester oil dry ice was treated as a trendsetter and indicated an 11% improvement of the tool life at a cutting speed of 75 m/min and a feed rate of 0.04 mm/z. Therefore, dry-ice-based hybrid lubri-coolant can be applied as a cutting fluid by practitioners in aerospace, automotive, prosthetic body parts manufacturing, and manufacturing industries.

A novel Laser-induced Fluorescence Concept for Thermometry Measurements in Machining Lubricoolants

Film Temperature And Thickness Measurements Of An Impinging Oil Jet For Cooling Of Electric Components Based On Two-Color Laser-Induced Fluorescence.

Simultaneous film temperature and film thickness measurements for jet impingement applications using two-color laser-induced fluorescence

Spectral Investigations of Fluorescence Tracers in Automotive and Aviation Fuels under Cryogenic Conditions

In-situ sub-angstrom characterization of laser-lubricant interaction in a thermo-tribological system

Simultaneous temperature and thickness measurements of falling liquid films by laser-induced fluorescence

High-sensitivity Ratiometric Thermometers of Yb3+/Er3+/Tm3+ Co-Doped LuScO3 Single Crystal Fibers Based on Non-Thermally Coupled Energy Levels

Optical Temperature Sensor Evaluation in a Working Gear Motor: Application of Luminescence Thermometry in Industrial Technology

High-sensitivity Ratiometric Thermometers of Yb 3+/er 3+/tm 3+Co-Doped LuScO 3 Single Crystal Fibers Based on Non-Thermally Coupled Energy Levels

Two-dye two-color laser-induced fluorescence spectroscopy on droplets of green solvent water/ethanol mixtures for thermometry and mixture composition

Optical Temperature Field Measurements With Two-Color Laser Induced Fluorescence In A Stratified Thermal Energy Storage

Defect induced luminescence from surface modified calcium fluoride nanoparticles for in-situ temperature monitoring of lubricating oil

Wassergekühlte Messlanze zur Laser-Doppler-Anemometrie in semi-industriellen Flammen

Identification and qualification of temperature signal for monitoring and control in laser cladding

Laser-spot lock-in thermography with a non-research-grade thermal camera: From thermal diffusivity measurements to visualizing free convection

INVESTIGATION OF A QUASI-STEADY LIQUID CRYSTAL TECHNIQUE FOR FILM COOLING HEAT TRANSFER MEASUREMENTS

Whole field measurement of temperature in water using two-color laser induced fluorescence

Droplet temperature measurement based on 2-color laser-induced exciplex fluorescence

Film Thickness and Glycerol Concentration Mapping of Falling Films Based on Fluorescence and Near-Infrared Technique

Thermophysical Properties and Heat Transfer Performance of Novel Dry-Ice-Based Sustainable Hybrid Lubri-Coolant

In-situ monitoring of a laser metal deposition (LMD) process: comparison of MWIR, SWIR and high-speed NIR thermography