Abstract:An investigation was carried out to study the effect of changes in oil quality on its tribological performance using a tuning fork technology based oil sensor. In this research, a tribological testing system was commissioned, to simulate the piston ring-cylinder liner sliding contact, and to measure the lubricant condition in real-time using an oil sensor. Tribological contact between cylinder liners and piston rings in marine engines is the most affected region due to excessive thermo-mechanical stresses. At top dead centre, the effect of such stresses is at a maximum where piston-sliding speed is lowest, while the temperature is high due to fuel combustion, and radial load behind the piston rings compressing against the cylinder liner surface is at a maximum due to gas pressure and the compression fit of piston rings within the cylinder liner. At bottom dead centre, this effect is less severe due to a reduction in temperature and gas pressure on the piston rings, as the piston is positioned away from the combustion chamber. These two regions experience boundary lubrication conditions, where anti-wear and anti-friction additives are responsible for forming a protective lubricious film on sliding surfaces. At mid-stroke, piston-sliding speed is maximum, therefore, a full hydrodynamic film is formed in this region separating the piston rings and cylinder liner. The formation of oil film depends upon, the physical properties of oil (such as viscosity and density) under hydrodynamic lubrication conditions, and the oil chemistry (such as presence of additives in oil) under mixed or boundary lubrication conditions. Lubricants in marine engines undergo intense degradation in quality due to contamination with wear particles, water, soot, un-burnt fuel, coolant, and additives depletion. Such degradation of lubricants leads to a reduction in their capability to form a minimum thickness of oil film between two moving engine components to avoid direct metal-to-metal contact, which may cause wear. Therefore, monitoring the condition of marine engine lubricants is vital in order to predict any significant change in its quality. The results obtained from tribology testing and oil condition monitoring in the current research showed a good correlation and are useful to understand the performance of lubricants for piston ring-liner contacts.

Radiospectroscopic Study of Used Marine Oils

Analysis of ZDDP content and thermal decomposition in motor oils using NAA and NMR

Investigation of the Extraction Process in Gel‐spinning Technology for Ultrahigh‐molecular‐weight Polyethylene Fibers by Low‐field Nuclear Magnetic Resonance

Engine Oils in the Field: A Comprehensive Chemical Assessment of Engine Oil Degradation in a Passenger Car

Research for the degradation of in - Service automotive engine lubricant oil

Chemometric Classification of Motor Oils Using 1H NMR Spectroscopy With Simultaneous Phase and Baseline Optimization

Analysis of mechanical energy losses in marine diesels

Stable carbon and hydrogen isotopic fractionation of individual n-alkanes accompanying biodegradation: evidence from a group of progressively biodegraded oils

Changes in composition and distribution of pyrrolic nitrogen compounds in biodegraded oils

Analysis of Tribological Properties of Engine Lubricants Used in Hybrid Vehicles

Additives Depletion by Water Contamination and Its Influences on Engine Oil Performance

Performance Deterioration Analysis of the Used Gear Oil

Experimental Investigation into the Effects of Fuel Dilution on the Change in Chemical Properties of Lubricating Oil Used in Fuel Injection Pump of Pielstick PA4 V185 Marine Diesel Engine

A Comparative Study of the Tribological Performance of Two Oil-Soluble Ionic Liquids As Replacements for ZDDP (T204) Additives in Lubricants

Experimental Study on the Effect of Marine Engine Lubricant Degradation on Tribological Performance of Cylinder Liner and Piston Rings Contact Using a Tuning Fork Technology Based Oil Sensor

Antiwear Chemistry of ZDDP: Coupling Classical MD and Tight-Binding Quantum Chemical MD Methods (TB-QCMD)

Study on Phosphorous‐free Triazinyl Disulfides As Additives in Combustion Engine Base Oil

Monitoring the Oil of Wind-Turbine Gearboxes: Main Degradation Indicators and Detection Methods

Non-destructive Testing of Marine Diesel Engines Using Integration of Ferrographic Analysis and Spectrum Analysis

Novel 1H low field nuclear magnetic resonance applications for the field of biodiesel

The Synergistic Antiwear and Frictional Properties of Organic Molybdenum Compound with Zinc Dialkyldithiophosphate