Abstract:ConspectusPhotoelectrochemical water splitting is a promising avenue for sustainable production of hydrogen used in the chemical industry and hydrogen fuel cells. The basic components of most photoelectrochemical water splitting systems are semiconductor light absorbers coupled to electrocatalysts, which perform the desired chemical reactions. A critical challenge for the design of these systems is the lack of stability for the majority of desired semiconductors under operating water splitting conditions. One strategy to address this issue is to protect the semiconductor by covering it with a stabilizing insulator layer, creating a metal-insulator-semiconductor (MIS) architecture, which has demonstrated improved stability. In addition to enhanced stability, the insulator layer may significantly affect the electron and hole transfer, which governs the recombination rates. Furthermore, the insertion of an insulator layer leads to the introduction of additional insulator/electrocatalyst and insulator/semiconductor interfaces. These interfaces can impact the system's performance significantly, and they need to be carefully engineered to optimize the efficiencies of MIS systems. In this Account, we describe our recent progress in shedding light on the critical role of the insulator and the interfaces on the performance of MIS systems. We discuss our findings by focusing on the concrete example of planar n-type Si protected by a HfO2 insulator layer and coupled to a Ni or Ir electrocatalyst that performs the oxygen evolution reaction, one of the water splitting half-reactions. To improve our fundamental understanding of the insulator layer, we precisely control the HfO2 insulator thickness using atomic layer deposition (ALD), and we perform a series of rigorous electrochemical experiments coupled with theory and modeling. We demonstrate that by tuning the insulator thickness, we can control the flux and recombination of photogenerated electrons and holes to optimize the generated photovoltage. Despite optimizing the thickness, we find that the maximum generated photovoltage in MIS systems is often significantly lower than the upper performance limit, i.e., there are additional losses in the system that could not be addressed by optimizing the insulator thickness. We identify the sources of these losses and describe strategies to minimize them by a combination of improving the semiconductor light absorption, removing nonidealities associated with interfacial defects, and finding alternative insulators with improved charge carrier selectivity. Finally, we quantify the improvements that can be obtained by implementing these specific strategies. Our collective work outlines strategies to analyze MIS systems, identify the sources of efficiency losses, and optimize the design to approach the fundamental performance limits. These general approaches are broadly applicable to photoelectrochemical materials that utilize sunlight to produce value-added chemicals.

Stabilization of Silicon Photoanode By Hafnium Zirconium Oxide Interlayer for Efficient Solar Water Oxidation

Low-cost, scalable, highly stable Si-based metal-insulator-semiconductor photoanodes for water oxidation fabricated using thin-film reactions and electrodeposition

Stable Silicon-Based Sandwich Photoelectrode for Efficient Solar Hydrogen Evolution

A Thin-Film Silicon Based Photocathode With A Hydrogen Doped Tio2 Protection Layer For Solar Hydrogen Evolution

High Performance P-Si/ni3s2 Photocathode for Photoelectrochemical Hydrogen Evolution in Neutral Solution

High-Performance Silicon Photoanodes Passivated with Ultrathin Nickel Films for Water Oxidation

Design Principles for Efficient and Stable Water Splitting Photoelectrocatalysts

An Interface‐cascading Silicon Photoanode with Strengthened Built‐in Electric Field and Enriched Surface Oxygen Vacancies for Efficient Photoelectrochemical Water Splitting

Achieving 12.0% Solar-to-Hydrogen Efficiency with a Trimetallic-Layer-Protected and Catalyzed Silicon Photoanode Coupled with an Inexpensive Silicon Solar Cell

n‐ZrS3/p‐ZrOS Photoanodes with NiOOH/FeOOH Oxygen Evolution Catalysts for Photoelectrochemical Water Oxidation

Conductive layer protected and oxide catalyst-coated thin-film silicon solar cell as an efficient photoanode

Highly Efficient NiFe Nanoparticle Decorated Si Photoanode for Photoelectrochemical Water Oxidation

A Silicon-Based Photocathode for Water Reduction with an Epitaxial SrTiO 3 Protection Layer and a Nanostructured Catalyst

Manipulating metal-oxygen local atomic structures in single-junctional p-Si/WO3 photocathodes for efficient solar hydrogen generation

Metal Sputtering Buffer Layer for High Performance Si-Based Water Oxidation Photoanode

Localized Dielectric Breakdown and Antireflection Coating in Metal–oxide–semiconductor Photoelectrodes

Oxygen-vacancy-rich nickel hydroxide nanosheet: a multifunctional layer between Ir and Si toward enhanced solar hydrogen production in alkaline media

Gradient‐Structuring Manipulation in Ni 3 S 2 Layer Boosts Solar Hydrogen Production of Si Photocathode in Alkaline Media

High‐Performance and Stable Silicon Photoanode Modified by Crystalline Ni@ Amorphous Co Core‐Shell Nanoparticles

Efficient photoelectrochemical water oxidation enabled by an amorphous metal oxide-catalyzed graphene/silicon heterojunction photoanode

Ultrathin MoS2-coated Ag@Si Nanosphere Arrays As an Efficient and Stable Photocathode for Solar-Driven Hydrogen Production.