Abstract:With the fast growth of consumer electronics market and wide commercialization of electric vehicles, the demand for advanced energy storage devices is soaring. The lithium ion battery is considered one of the most promising candidates to satisfy this demand due to its high energy density, superior cyclability, and low cost [1-3]. Since its discovery in 1991, LiCoO 2 has been commercially adopted as the intercalation compound for li-ion batteries because it is easy to synthesize, has high theoretical specific capacity, and has good reversibility [4,5]. However, high cost and high toxicity are associated with the use of Co [6, 7]. LiNiO 2 and LiMn 2 O 4 are two feasible replacement materials for LiCoO 2 , but they come with challenges and limitations. Although LiNiO 2 demonstrates higher specific capacity than LiCoO 2, phase transition of LiNiO 2 from hexagonal to cubic crystals occurs during the deintercalation process of the li-ion, and this dramatically reduces the reversible capacity of the material [8-9]. On the other hand, LiMn 2 O 4 reacts with the electrolyte when the cell temperature exceeds 55 °C, leading to dissolution of manganese and the subsequent loss of capacity [10,11]. A novel cathode material, LiNi 1/3 Co 1/3 Mn 1/3 O 2 , was initially proposed by Ohzuku et al. back in 2001 [12]. This ternary solid solution preserves the benefits of LiCoO 2 , LiNiO 2 and LiMn 2 O 4 by synergizing three transition metal elements all at once. By partially substituting Co with Ni in LiCoO 2 , higher specific capacity can be achieved [13]. The presence of electrochemically inactive Mn 4+ in the lattice effectively suppress the phase transition of LiNiO 2 , which improves the structural stability during cycling and enables a higher charge voltage without compromising the thermal stability of the cathode at the highly delithiated states [14,15]. More li-ions are impelled to intercalate and deintercalate from the electrode if the upper cut-off voltage is elevated from 4.2 to 4.5V or even higher, translating into a noticeable gain in the specific capacity and, in turn, a significant increase in energy density [16]. The remaining Co plays an important role in enhancing the conductivity of the NMC compound [17]. Moreover, only small volume change results from the insertion and extraction of li-ions in NMC electrode, leading to better cycling stability and longer cell life [18]. Numerous synthesis techniques have been employed to prepare NMC, including solid state reaction, co-precipitation, sol-gel and hydrothermal reaction [19-22]. However, several shortcomings are associated with these processes, such as structural inhomogeneity, irregular morphology, a series of time-consuming steps, and poor control of the particle size. Reactive spray deposition technology (RSDT), a single-step flame based deposition method, is capable of synthesizing and depositing NMC nanoparticles directly onto a stainless steel current collector to form a thin film electrode. The as-deposited electrode is ready for electrochemical testing in a coin cell assembly without further processing. The electrochemical properties of these synthesized materials can be fine-tuned by manipulation of several key RSDT operating parameters. The particle size distribution and surface morphology of the deposited film can be well controlled through modifying the reactant concentration in the solvent, the feed rate of the precursor solution, and the flow rate of oxidant gases. The nanostructure of the LiNi 1/3 Mn 1/3 Co 1/3 O 2 cathode fabricated by RSDT significantly shortens the diffusion length for the li-ions, offering potential to improve rate capability [23]. References: M.S. Whittingham, Chem. Rev. 104 (2004) 4271-4302. M.R. Palacín, Soc. Rev. 38 (2009) 2565-2575. C. Liu, et al., Adv. Mater. 22 (2010) E28-E62. T. Ohzuku, J. Power Sources 174 (2007) 449. T. Nagaura, Prog. Batter. Battery Mater. 10 (1991) 18-26. G. Ceder, et al., Nature 392 (1998) 694. R. Thirunakaran, et al., Ionics 9 (2003) 388-394. P. Kalyani, N. Kalaiselvi, Sci. Technol. Adv. Mater. 6 (2005) 689–703. W. Li, et al., Solid State Ionics 67 (1993) 123. W.J. Zhou, et al., Electrochim. Acta 51 (2006) 4701. G.G. Amatucci, et al., J. Power Sources 69 (1997) 11-25. T. Ohzuku, Y. Makimura, Chem. Lett. 7 (2001) 642-643. T. Ohzuku, et al., Electrochim. Acta 38 (1993) 1159. X. Li, et al., Energy Environ. Sci. 7 (2014) 768-778. K.S. Lee, et al., J. Electrochem. Soc. 154 (2007) A971-A977. S.K. Kim, et al., Int. J. Electrochem. Sci. 3 (2008) 1504–1511. H.J. Noh, et al., J. Power Sources 233 (2013) 121–130. J.M. Kim, H.T. Chung, Electrochim. Acta 49 (2004) 937. K.C. Mahesh, et al., J. Electrochem. Soc. 159 (2012) A1040-A1047. S.Y. Yang, et al., J. Solid State Electrochem. 16 (2012) 481-490. W. Zhang, et al., Rare Met. 27 (2008) 158–164. J.L. Xie, et al., Ceram. Int. 36 (2010) 2485-2487. F. Wang, et al., Chem. Commun. 49 (2013) 9209-9211.

A Scalable Approach to Synthesize Cobalt-Free LNMO Cathode Materials for High Energy Density Lithium Ion Batteries

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Optimized Morphology and Tuning the Mn3+ Content of LiNi0.5Mn1.5O4 Cathode Material for Li-Ion Batteries

Solution-Based Synthesis of Cathode Materials for Lithium Ion Batteries

A Practical and Sustainable Ni/Co-Free High-Energy Electrode Material: Nanostructured LiMnO2

Preparation of High Performance LiNi 0.5 Mn 1.5 O 4 Materials and Metal Doping

(Invited) Delineating the Intricacies Involved in the Synthesis of Cobalt-Free High-Nickel Layered Oxide Cathodes for Lithium-Ion Batteries

Tailoring Co‐Free LiNi0.5Mn1.5O4 Material for High‐Voltage Lithium‐Ion Batteries: Particle Design & Grain Boundary Engineering

One-Step Fabrication of Nanostructured LiNi1/3Mn1/3Co1/3O2 Cathode for Lithium Ion Batteries

Systematic Optimization of Battery Materials: Key Parameter Optimization for the Scalable Synthesis of Uniform, High-Energy, and High Stability LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode Material for Lithium-Ion Batteries

A 5V-class Cobalt-free Battery Cathode with High Loading Enabled by Dry Coating

Development and understanding of the lithiation/de-lithiation mechanism of a low cobalt and nickel-rich cathode material for lithium‐ion batteries

(Digital Presentation) Cobalt Free Cathode Synthesized By Sacrificial Template (α-MnOOH) for Rechargeable Lithium Batteries

Microwave Plasma Synthesis of Cathode Material for Lithium-Ion Batteries

Pushing the Energy-Lifetime Frontier of Li-Ion Batteries with Optimized Ni-Rich, Co-Free NMA-W Cathodes

Effect of Calcination Temperature on the Structural and Electrochemical Properties of NMC Cathodes for Lithium-Ion Batteries

Micron-Sized Monodisperse Particle LiNi0.6Co0.2Mn0.2O2 Derived by Oxalate Solvothermal Process Combined with Calcination as Cathode Material for Lithium-Ion Batteries

The Correlation Between Structure, Surface, and Performance in Fe- and Mg-Substituted LiNi0.5Mn1.5O4 Cathodes

Advances in modification methods and the future prospects of high-voltage spinel LiNi<sub>0.5</sub>Mn<sub>1.5</sub>O<sub>4</sub> - a review

Improving Fast-Charging Capability of High-Voltage Spinel LiNi0.5Mn1.5O4 Cathode under Long-Term Cyclability Through Co-Doping Strategy

Optimization of Synthesis Parameters for Uniform Sphere-Like Li1.2Mn0.54Ni0.13Co0.13O2 As High Performance Cathode Material for Lithium Ion Batteries