Abstract:Catalyzed by a phenoxycyclopentylimine ligated zirconium complex/dried methylaluminoxane (dMAO) system at 40 degrees C under 1 atm of ethylene pressure, linear vinyl-terminated polyethylene (PE-ene) with nearly 100% of end-functionality was produced via ethylene polymerization. With high efficiency, hydroxyl-terminated polyethylene (PE-OH) was subsequently prepared via the radical initiated thiol-ene click chemistry between the PE-ene and 2-mercaptoethanol. The PE-OH was then used to react with norbornene-5-carbonyl chloride to synthesize the norbornene-terminated polyethylene macromonomer (PE-NB) through the esterification reaction. The ring-opening metathesis copolymerization (ROMP) of PE-NB and norbornene (NB) with the different feed ratio was conducted in the presence of Grubbs II generation catalyst to produce the polyethylene-based graft copolymers. Both random and block polynorbornene-g-polyethylene graft copolymers (PNB-g-PE) were then obtained with different feeding mode, i.e., the one-batch feeding mode and the sequential feeding mode, respectively. The structures of the graft copolymers were characterized by Fourier transform-infrared and proton nuclear magnetic resonance spectroscopy. The molecular weight and molecular weight distribution of PNB-g-PE were determined by high-temperature gel permeation chromatography; the thermal properties of PNB-g-PE were also tested by differential scanning calorimetry. The conversion of macromonomer was found to be nearly 100% in the random copolymerization of macromonomer and norbornene. The random graft copolymers were obtained with the molecular weight of 1.79 x 10(4) - 3.14 x 10(4) with relatively narrow molecular weight distribution (2.09 - 2.60). The molecular weight of the copolymers decreased gradually with the increase in the feed ratio of PE-NB. The molar fraction of PE in the random copolymers varied from 4.6% to 16.8%, depending on the feed ratio of PE-NB to NB, whereas the molar fraction of PE showed slight influence on the melting point of the PE segments. However, the conversion of macromonomer reached about 80% in the block copolymerization of PE-NB and NB. Due to the steric hindrance, the crystallinity of the graft copolymers slightly decreased in comparison with the corresponding PE precursor.

Keto-Polyethylenes with Controlled Crystallinity and Materials Properties from Catalytic Ethylene–CO–Norbornene Terpolymerization

Preparation Of Comb-Shaped Polyolefin Elastomers Having Ethylene/1-Octene Copolymer Backbone And Long Chain Polyethylene Branches Via A Tandem Metallocene Catalyst System

Studies on Alternating Copolymerization of Ethylene and Carbon Monoxide Using Nickel‐Based Catalyst: Cocatalyst and the Polarity of Solvent

Modification of Poly(ethylene 2,5-Furandicarboxylate) with Aliphatic Polycarbonate Diols: 1. Randomnized Copolymers with Significantly Improved Ductility and High CO2 Barrier Performance

Precision Copolymerization of CO 2 and Epoxides Enabled by Organoboron Catalysts

Preparation of Polyethylene-Based Random and Block Graft Copolymers

Pinwheel-Shaped Tetranuclear Organoboron Catalysts for Perfectly Alternating Copolymerization of CO2 and Epichlorohydrin.

Modification of Poly(ethylene furandicarboxylate) with Aliphatic Polycarbonate diols: 1. Randomnized Copolymers with Significantly Improved Ductility and High CO2 Barrier Performance

Carbonyl Functionalized Polyethylene Materials via Ni- and Pd-diphosphazane Monoxide Catalyzed Nonalternating Copolymerization

Polyethylene Materials with In-Chain Ketones from Catalytic Copolymerization

Aqueous Keto-Polyethylene Dispersions from Catalytic Copolymerization of Ethylene and Carbon Monoxide in Water

Circular Cross-Linked Polyethylene Enabled by In-Chain Ketones

Synthesis of Nonalternating Polyketones Using Cationic Diphosphazane Monoxide-Palladium Complexes

Cationic Palladium Catalyzed Nonalternating Copolymerization of Ethylene with Carbon Monoxide: Microstructure Analysis and Computational Study

Synthesis of Polyethylenes with In-Chain Isolated Carbonyls from CO 2 and Ethylene Via a Tandem Photoreduction/Polymerization Protocol

A Topology‐Defined Polyester Elastomer from CO2 and 1,3‐butadiene: A One‐Pot‐One‐Step “scrambling Polymerizations” Strategy

Polyethylene materials with in-chain ketones from nonalternating catalytic copolymerization

Preparation of carbon dioxide, propylene oxide, and norbornene dianhydride terpolymers catalyzed via dinuclear cobalt complexes: Effective improvement of thermal, mechanical, and degradation properties

Recent Advances in Synthesis of Non-Alternating Polyketone Generated by Copolymerization of Carbon Monoxide and Ethylene

Aliphatic Polyketones Via Cross-Metathesis Polymerization: Synthesis and Post-Polymerization Modification

Cyclic olefin copolymers containing both linear polyethylene and poly(ethylene- co -norbornene) segments prepared from chain shuttling copolymerization of ethylene and norbornene