Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Theoretical investigation the effect of A-site elements on mechanical and thermal properties in Ti 2 AC (A = Al, Ga, In, Si, Ge, Sn) compounds

Chemical Bonding and Elastic Properties of Ti3AC2 Phases (A = Si, Ge, and Sn): A First-Principle Study

Theoretical Investigation of A-element Atom Diffusion in Ti2AC (a=sn, Ga, Cd, In, and Pb)

Insights into the Mechanical Properties and Thermal Transport of Ti3(Al1-xAx)C2 Solid Solutions: A Comprehensive Theoretical Study Combined with Experiment

Effect of Zr, Hf, and Sn Additives on Elastic Properties of Α2-Ti3al Phase by First-Principles Calculations

First Principles Studies on the Elastic, Thermodynamic Properties and Electronic Structure of Ti15−xMoxSn Compounds

Pressure prediction of phase stability, anisotropic elasticity, and thermodynamic properties of Ti<sub>2</sub>AC (A = Cd, In) ternary compound

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Phase Stability, Mechanical Properties and Electronic Structures of TiAl Binary Compounds by First Principles Calculations

Mechanical properties and wear behavior of Tin+1(Al, A)Cn (A = Ga, In, Sn, n = 1, 2) via quasi-high-entropy of single atomic thick A layer

First-principles calculation on the structural, elastic and thermodynamic properties of Ti-Al intermetallics

Investigation of the Physical Properties of the Metal (co, Cr, Mn, Sc) Doped TiAl3 Compounds: A DFT Study

Screen the elastic and thermodynamic properties of MAX solid solution using DFT procedue: Case study on (Ti1-xVx)2AlC

Mechanical And Electronic Properties Of Antiperovskite Ti-Based Compounds Axti(3) (X = C, N): A First-Principles Investigation

First-principles Calculations to Investigate Elastic Properties, Ideal Tensile Strength and Electronic Properties of TiSi, Ti5Si3 and Ti5Si4

Role of the A-Element in the Structural, Mechanical, and Electronic Properties of Ti 3 AC 2 MAX Phases

Ab Initio Geometry Optimization and Ground State Properties of Layered Ternary Carbides Ti3mc2 (M = Al, Si and Ge)

Effects of alloying elements on the atomic structure, elastic and thermodynamic properties of L12-Co3(V, Ti) compound

First-Principles Investigations of the Structural, Anisotropic Mechanical, Thermodynamic and Electronic Properties of the AlNi2Ti Compound

Investigation on the effect of alloying elements on the Ti 2 AlC/TiAl interfacial properties: First-principles prediction and experimental verification

Ab initio study of the bonding and elastic properties of Ti2CdC