[Problems of diagnosis in chronic pyelonephritis].

G. Lenti,A. Vercellone,D. Varese,G. Piccoli

1961-04-01

Abstract:

What problem does this paper attempt to address?

A Col E1 hybrid plasmid containing Escherichia coli genes complementing d-xylose negative mutants of Escherichia coli and Salmonella typhimurium.

R. Maleszka,P. Wang,H. Schneider

DOI: https://doi.org/10.1139/O82-020

1982-02-01

Canadian Journal of Biochemistry

Abstract:The Clarke and Carbon bank of Col El - Escherichia coli DNa hybrid plasmids was screened for complementation of d-xylose negative mutants of E. coli. Of several obtained, the smallest, pRM10, was chosen for detailed study. Its size was 16 kilobases (kb) and that of the insert was 9.7 kg. By transformation or F'-mediated conjugation this plasmid complemented mutants of E. coli defective in either D-xylose isomerase or D-xylulose kinase activity, or both. The activity of D-xylulose kinase in E. coli transformants which bear an intact chromosomal gene for this enzyme was greater than that for the host, due to a gene dosage effect. The plasmid also complemented D-xylose negative mutants of Salmonella typhimurium by F'-mediated conjugation between E. coli and S. typhimurium. Salmonella typhimurium mutants complemented were those for D-xylose isomerase and for D-xylulose kinase in addition to pleiotropic D-xylose mutants which were defective in a regulatory gene of the D-xylose operon. In addition, the plasmid complemented the glyS mutation in E. coli and S. typhimurium. The glyS mutant of E. coli was temperature sensitive, indicating that the plasmid carried the structural gene for glycine synthetase. The glyS mutation in E. coli maps at 79 min, as do the xyl genes. The behaviour of the plasmid is consistent with the existence of a d-xylose operon in E. coli. The data also suggest that the plasmid carries three of the genes of this operon, specifically those for D-xylose isomerase, D-xylulose kinase, and a regulatory gene.
Microstructure evolution in a Fe-Ni-Si alloy during heat treatment and electron irradiation

S. E. Danilov,

DOI: https://doi.org/10.17804/2410-9908.2021.5.036-043

2021-10-01

Abstract:Experiments have been made on studying structural and phase changes by the residual resistivity method in a Fe-Ni-Si alloy during annealing and electron irradiation. Thermal diffusion starts above 600 K and ensures decomposition of the solid solution up to 700 K; at higher temperatures it provides homogenization of the solid solution with the dissolution of intermetallic compounds in accordance with the equilibrium phase diagram. It is shown that, upon irradiation with electrons above 240 K, vacancy clusters are formed in both the aged and quenched alloys. Dissociation of clusters occurs at temperatures ranging between 350 and 500 K and leads to solid solution decomposition under the influence of diffusion caused by migrating vacancies with the formation of intermetallic precipitates. Irradiation at 423 K causes migration of vacancies and decomposition of the solid solution. In alloys irradiated at both temperatures above 700 K, as well as in unirradiated alloys, the precipitates dissolve in accordance with a single equilibrium dependence.
Direct Observation of Defect Range and Evolution in Ion-Irradiated Single Crystalline Ni and Ni Binary Alloys

Chenyang Lu,Ke Jin,Laurent K. Béland,Feifei Zhang,Taini Yang,Liang Qiao,Yanwen Zhang,Hongbin Bei,Hans M. Christen,Roger E. Stoller,Lumin Wang

DOI: https://doi.org/10.1038/srep19994

IF: 4.6

2016-02-01

Scientific Reports

Abstract:AbstractEnergetic ions have been widely used to evaluate the irradiation tolerance of structural materials for nuclear power applications and to modify material properties. It is important to understand the defect production, annihilation and migration mechanisms during and after collision cascades. In this study, single crystalline pure nickel metal and single-phase concentrated solid solution alloys of 50%Ni50%Co (NiCo) and 50%Ni50%Fe (NiFe) without apparent preexisting defect sinks were employed to study defect dynamics under ion irradiation. Both cross-sectional transmission electron microscopy characterization (TEM) and Rutherford backscattering spectrometry channeling (RBS-C) spectra show that the range of radiation-induced defect clusters far exceed the theoretically predicted depth in all materials after high-dose irradiation. Defects in nickel migrate faster than in NiCo and NiFe. Both vacancy-type stacking fault tetrahedra (SFT) and interstitial loops coexist in the same region, which is consistent with molecular dynamics simulations. Kinetic activation relaxation technique (k-ART) simulations for nickel showed that small vacancy clusters, such as di-vacancies and tri-vacancies, created by collision cascades are highly mobile, even at room temperature. The slower migration of defects in the alloy along with more localized energy dissipation of the displacement cascade may lead to enhanced radiation tolerance.

multidisciplinary sciences
Formation of helical dislocations mediated by interstitials in ion irradiated FeCrAl alloy

Yipeng Li,Zhipeng Sun,Nan Liao,Ziqi Cao,Xinyi Liu,Yuanming Li,Yifan Ding,Xi Qiu,Guang Ran

DOI: https://doi.org/10.1016/j.jnucmat.2023.154413

IF: 3.555

2023-03-28

Journal of Nuclear Materials

Abstract:Unraveling the interaction of the pre-existing dislocations with irradiation defects is crucial to understanding the microstructural evolution and the strength-ductility trade-off of iron-based alloys under service in an irradiation environment. In this work, the formation of helical dislocations was analyzed by combining an in-situ experiment of 400 keV Fe + irradiated Fe-13.2Cr-5.6Al alloy at 823 K with molecular dynamics (MD) simulations. A mechanism that irradiation induced interstitial defects would mediate the pre-existing screw dislocation to produce the helical dislocations was revealed. The in-situ formation of helical dislocations and the absence of dislocation loop in the vicinity of helical dislocations were observed. The helical dislocations more likely form in the region with higher pre-existing screw dislocation density, but it will be suppressed by the dislocation loops nucleating near the screw dislocations.

materials science, multidisciplinary,nuclear science & technology
Self-ion Irradiation Response of (cocrfeni)94ti2al4 Alloy Containing Coherent Nanoprecipitates

Y. Zheng,W. Lu,F. Qian,N. Jia,Y. Dou,X. He,W. Yang,J. Wang,Y. Xue,K. Jin

DOI: https://doi.org/10.1016/j.jnucmat.2021.152889

IF: 3.555

2021-01-01

Journal of Nuclear Materials

Abstract:In order to investigate the impact of coherent nanoprecipitates on the irradiation-induced microstructural change in high-entropy alloys and the stability of nanoprecipitates under irradiation, the single-phase CoCrFeNi and the coherent nanoprecipitate-containing (CoCrFeNi)94Ti2Al4 alloys were irradiated with 2.7 MeV Fe ions at 823 K. With the introduction of L12 coherent nanoprecipitates, the size of irradiation-induced dislocation loops is significantly reduced and the unfaulting of faulted loops is delayed. Unlike that both Ni and Co are segregated towards the loops in CoCrFeNi, the enrichment of Ni at loops is suppressed in (CoCrFeNi)94Ti2Al4 with the co-existence of nanoprecipitates. Furthermore, although minor coarsening and dissolution of nanoprecipitates are observed after irradiation, the stability is enhanced compared with some conventional Ni-based alloys.
The Effect of Dislocations on MnNi-rich Clusters in Self-Ion Irradiated FeMnNi Alloy

Hailong Liu,Qiulin Li,Ben Xu,Wei Liu,Guogang Shu

DOI: https://doi.org/10.1016/j.jnucmat.2019.03.017

IF: 3.555

2019-01-01

Journal of Nuclear Materials

Abstract:The effect of dislocations on irradiation-induced MnNi-rich clusters in self-ion irradiated FeMnNi alloy was investigated using X-ray diffraction (XRD), nanoindentation, positron annihilation Doppler broadening spectroscopy (PADBS), and atom probe tomography (APT). The nanoindentation results showed that irradiation-induced hardening decreased with dislocation density increasing. The results of APT and PADBS revealed that high-energy Fe-ion irradiation generates high-density MnNi-rich clusters and large vacancy-type defects in irradiated FeMnNi alloy. Note that dense dislocations suppress the formation of large vacancy-type defects and MnNi-rich clusters. By analyzing the effect of dislocations on point defects (PDs), diffusion of Mn and Ni atoms, and nucleation of MnNi-rich clusters, we found that nucleation mechanism of MnNi-rich clusters is strongly dependent on the flux of PDs. However, high-density dislocations can facilitate to annihilate irradiation-induced PDs and cause the decline of defect-solute coupling fluxes, which are responsible for a reduction in number density and mole fraction of MnNi-rich clusters.
Effect of Carbon on Dislocation Loops Formation during Self-Ion Irradiation in Fe-Cr Alloys at High Temperatures

Tiantian Shi,Wenbo Liu,Zhengxiong Su,Xu Yan,Chenyang Lu,Di Yun

DOI: https://doi.org/10.3390/ma15062211

IF: 3.4

2022-03-17

Materials

Abstract:In this study, two types of ferritic model alloys (Fe-9Cr and Fe-9Cr-C) were simultaneously irradiated with 3.5 MeV Fe13+ ions at 450 °C and 550 °C to a dose of 3dpa at the peak damage region, respectively. Transmission electron microscopy (TEM) was used to investigate the microstructural evolution of the Fe-Cr alloys after irradiation. The experimental results showed that the size of the dislocation loops formed in the Fe-9Cr-C alloy was larger than that in the Fe-9Cr alloy, but the loop density of the Fe-9Cr-C alloy was lower than that of the Fe-9Cr alloy after irradiation at 450 °C. The reason for this phenomenon was attributed to the fact that loops formed in Fe-9Cr-C alloy have greater capture efficiency for interstitial atoms. Compared to Fe-Cr alloys irradiated at 450 °C, high-density loops were not observed in the Fe-Cr alloys irradiated at 550 °C; the number of dislocation loops in the Fe-Cr alloys irradiated at 550 °C significantly decreased due to the rapid conversion of the dislocation loops into network dislocations. In addition, subgrains were observed in the Fe-Cr alloys after irradiation. The underlying reason behind the formation of subgrains is discussed in detail.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Deuterium Ion Irradiation Induced Precipitation in Fe–Cr Alloy: Characterization and Effects on Irradiation Behavior

P. P. Liu,R. Yu,Y. M. Zhu,M. Z. Zhao,J. W. Bai,F. R. Wan,Q. Zhan

DOI: https://doi.org/10.1016/j.jnucmat.2014.12.124

IF: 3.555

2015-01-01

Journal of Nuclear Materials

Abstract:A new phase was found to precipitate in a Fe-Cr model alloy after 58 keV deuterium ion irradiation at 773 K. The nanoscale radiation-induced precipitate was studied systematically using high resolution transmission electron microscopy (HRTEM), image simulation and in-situ ultrahigh voltage transmission electron microscopy (HVEM). B2 structure is proposed for the new Cr-rich phase, which adopts a cubeon-cube orientation relationship with regard to the Fe matrix. Geometric phase analysis (GPA) was employed to measure the strain fields around the precipitate and this was used to explain its characteristic 1-dimensional elongation along the [1 0 0] Fe direction. The precipitate was stable under subsequent electron irradiation at different temperatures. We suggest that the precipitate with a high interface-to-volume ratio enhances the radiation resistance of the material. The reason for this is the presence of a large number of interfaces between the precipitate and the matrix, which may greatly reduce the concentration of point defects around the dislocation loops. This leads to a significant decrease in the growth rate. (C) 2015 Elsevier B.V. All rights reserved.
Deformation Localisation in Ion-Irradiated FeCr

Kay Song,Dina Sheyfer,Wenjun Liu,Jonathan Z Tischler,Suchandrima Das,Kenichiro Mizohata,Hongbing Yu,David E J Armstrong,Felix Hofmann

2023-10-03

Abstract:Irradiation-induced ductility loss is a major concern facing structural steels in next-generation nuclear reactors. Currently, the mechanisms for this are unclear but crucial to address for the design of reactor components. Here, the deformation characteristics around nanoindents in Fe and Fe10Cr irradiated with Fe ions to $\sim$1 displacement-per-atom at 313 K are non-destructively studied. Deformation localisation in the irradiated materials is evident from the increased pile-up height and slip step formation, measured by atomic force microscopy. From 3D X-ray Laue diffraction, measurements of lattice rotation and strain fields near the indent site show a large confinement, over 85%, of plasticity in the irradiated material. We find that despite causing increased irradiation hardening, Cr content has little effect on the irradiation-induced changes in pile-up topography and deformation fields. The results demonstrate that varying Cr content in steels has limited impact on retaining strain hardening capacity and reducing irradiation-induced embrittlement.

Materials Science
Observations of Percolation Structures Induced in Thin Solid Films by Ion Irradiation

Ding Juren,Huang Liji,Liu Baixin

DOI: https://doi.org/10.1088/0256-307x/5/7/009

1988-01-01

Abstract:Percolation structures of precipitated new phases were observed in Au-Ti and Ni-Al amorphous films upon ion irradiation. The experimental evidences showed that the observed structures were formed in the surface layer, ca 20nm thick. It was revealed that the formation of percolation clusters was sensitive to alloy composition as well as irradiation dose.
Observations of Fractal Patterns Induced in Thin Solid Films by Ion Irradiation.

BX LIU,LJ HUANG,K TAO,CH SHANG,HD LI

DOI: https://doi.org/10.1103/physrevlett.59.745

IF: 8.6

1987-01-01

Physical Review Letters

Abstract:The formation of fractal patterns during an amorphous structural transition in Ni-Mo thin films after 200-keV xenon-ion irradiation is presented. The dimension of the ion-induced fractals is 1.72\ifmmode\pm\else\textpm\fi{}0.07. The fractal patterns, together with other microscopic features, are described and characterized. Our results are compared to the cluster-diffusion-limited-aggregation model. The growth habit is attributed to long-range correlation which occurs at a critical condition during the amorphous-crystal transition.
In Situ Transmission Electron Microscopy Study of Growth of Dislocation Loops in Fe-Ni Alloy under Ion Irradiation

Liang Chen,Kenta Murakami,Dongyue Chen,Hiroaki Abe,Zhengcao Li,Naoto Sekimura

DOI: https://doi.org/10.1016/j.scriptamat.2020.06.071

IF: 6.302

2020-01-01

Scripta Materialia

Abstract:In situ irradiation in transmission electron microscope following pre-irradiation was performed on Fe-0.6Ni alloy to investigate the growth of dislocation loops under irradiation. The observations showed two types of loop growth behaviour. One type was almost linear growth with irradiation dose, possibly caused by loop absorbing freely migrating defects. The other was abrupt growth with rapid increase in diameter. It was found that nanometre-sized loop might migrate one-dimensionally, following which the large loop could absorb the small loop. This process can result in the abrupt growth of loop and broadening of loop size distribution.
Radiation-induced softening of Fe and Fe-based alloys during in-situ electron irradiation under mechanical testing

V.I. Dubinko,D. Terentyev,A.N. Dovbnya,V.A. Kushnir,I.V. Hodak,S.V. Lebedev,S.A. Kotrechko,A.V. Dubinko

DOI: https://doi.org/10.48550/arXiv.1409.6799

2014-09-24

Abstract:Defects formed under irradiation in the bulk act as additional pinning centers resulting in the well-known effect of radiation-induced hardening. On the other hand, there is a poorly understood but well-established effect of instant and reversible softening of metals subjected to various types of irradiation. This radiation-induced softening (RIS) effect should be taken into account both in the theory of radiation effects and in the engineering approach for technological applications. In the present paper, the RIS is investigated experimentally in polycrystalline technically pure iron (0.048%C) and in commercial ferritic steel. The effect of the electron beam on plastic deformation of bcc Fe is compared with that in fcc Al (99.5%). Electron energy ranged from 0.5 to 0.8 MeV. Reversible drop of the yield stress and radiation-induced reduction of the elongation to fracture are measured as functions of the electron current and specimen thickness. Rate theory of RIS is proposed, which takes into account the radiation-induced excitation of moving discrete breathers (DBs), recently proven to exist in bcc Fe, and their interaction with dislocations enhancing unpinning from structural defects. The behavior of the DBs is studied using classical MD simulations providing input for the modified rate theory, which eventually demonstrates a reasonable agreement with experimental data. The relevance of results to the in-reactor behavior of pressure vessel steels is discussed.

Materials Science
Characterising Ion-Irradiated FeCr: Hardness, Thermal Diffusivity and Lattice Strain

Kay Song,Suchandrima Das,Abdallah Reza,Nicholas W. Phillips,Ruqing Xu,Hongbing Yu,Kenichiro Mizohata,David E. J. Armstrong,Felix Hofmann

DOI: https://doi.org/10.1016/j.actamat.2020.10.015

2020-10-02

Abstract:Ion-irradiated FeCr alloys are useful for understanding and predicting neutron-damage in the structural steels of future nuclear reactors. Previous studies have largely focused on the structure of irradiation-induced defects, probed by transmission electron microscopy (TEM), as well as changes in mechanical properties. Across these studies, a wide range of irradiation conditions has been employed on samples with different processing histories, which complicates the analysis of the relationship between defect structures and material properties. Furthermore, key properties, such as irradiation-induced changes in thermal transport and lattice strain, are little explored. Here we present a systematic study of Fe3Cr, Fe5Cr and Fe10Cr binary alloys implanted with 20 MeV Fe$^{3+}$ ions to nominal doses of 0.01 dpa and 0.1 dpa at room temperature. Nanoindentation, transient grating spectroscopy (TGS) and X-ray micro-beam Laue diffraction were used to study the changes in hardness, thermal diffusivity and strain in the material as a function of damage and Cr content. Our results suggest that Cr leads to an increased retention of irradiation-induced defects, causing substantial changes in hardness and lattice strain. However, thermal diffusivity varies little with increasing damage and instead degrades significantly with increasing Cr content in the material. We find significant lattice strains even in samples exposed to a nominal displacement damage of 0.01 dpa. The defect density predicted from the lattice strain measurements is significantly higher than that observed in previous TEM studies, suggesting that TEM may not fully capture the irradiation-induced defect population.

Materials Science
Deformation Behaviour of Ion-Irradiated FeCr: A Nanoindentation Study

Kay Song,Hongbing Yu,Phani Karamched,Kenichiro Mizohata,David Armstrong,Felix Hofmann

DOI: https://doi.org/10.1557/s43578-022-00613-2

2021-07-20

Abstract:Understanding the mechanisms of plasticity in structural steels is essential for the operation of next-generation fusion reactors. Elemental composition, particularly the amount of Cr present, and irradiation can have separate and synergistic effects on the mechanical properties of ferritic/martensitic steels. The study of ion-irradiated FeCr alloys is useful for gaining a mechanistic understanding of irradiation damage in steels. Previous studies of ion-irradiated FeCr did not clearly distinguish between the nucleation of dislocations to initiate plasticity, and their propagation through the material as plasticity progresses. In this study, Fe3Cr, Fe5Cr, and Fe10Cr were irradiated with 20 MeV Fe$^{3+}$ ions at room temperature to nominal doses of 0.01 dpa and 0.1 dpa. Nanoindentation was carried out with Berkovich and spherical indenter tips to study the nucleation of dislocations and their subsequent propagation. The presence of irradiation-induced defects reduced the theoretical shear stress and barrier for dislocation nucleation. The presence of Cr further enhanced this effect due to increased retention of irradiation defects. However, this combined effect is still small compared to dislocation nucleation from pre-existing sources such as Frank-Read sources and grain boundaries. The yield strength, an indicator of dislocation mobility, of FeCr increased with irradiation damage and Cr. The increased retention of irradiation defects due to the presence of Cr also further increased the yield strength. Reduced work hardening capacity was also observed following irradiation. The synergistic effects of Cr and irradiation damage in FeCr appear to be more important for the propagation of dislocations, rather than their nucleation.

Materials Science
Dose and compositional dependence of irradiation-induced property change in FeCr

Kay Song,Dina Sheyfer,Kenichiro Mizohata,Minyi Zhang,Wenjun Liu,Doğa Gürsoy,David Yang,Ivan Tolkachev,Hongbing Yu,David E J Armstrong,Felix Hofmann

2024-03-04

Abstract:Ferritic/martensitic steels will be used as structural components in next generation nuclear reactors. Their successful operation relies on an understanding of irradiation-induced defect behaviour in the material. In this study, Fe and FeCr alloys (3-12%Cr) were irradiated with 20 MeV Fe-ions at 313 K to doses ranging between 0.00008 dpa to 6.0 dpa. This dose range covers six orders of magnitude, spanning low, transition and high dose regimes. Lattice strain and hardness in the irradiated material were characterised with micro-beam Laue X-ray diffraction and nanoindentation, respectively. Irradiation hardening was observed even at very low doses (0.00008 dpa) and showed a monotonic increase with dose up to 6.0 dpa. Lattice strain measurements of samples at 0.0008 dpa allow the calculation of equivalent Frenkel pair densities and corrections to the Norgett-Robinson-Torrens (NRT) model for Fe and FeCr alloys at low dose. NRT efficiency for FeCr is 0.2, which agrees with literature values for high irradiation energy. Lattice strain increases up to 0.8 dpa and then decreases when the damage dose is further increased. The strains measured in this study are lower and peak at a larger dose than predicted by atomistic simulations. This difference can be explained by taking temperature and impurities into account.

Materials Science
In situ microstructural evolution in face-centered and body-centered cubic complex concentrated solid-solution alloys under heavy ion irradiation

Calvin Parkin,Michael Moorehead,Mohamed Elbakhshwan,Jing Hu,Wei-Ying Chen,Meimei Li,Lingfeng He,Kumar Sridharan,Adrien Couet

DOI: https://doi.org/10.1016/j.actamat.2020.07.066

IF: 9.4

2020-10-01

Acta Materialia

Abstract:This study characterizes the microstructural evolution of single-phase complex concentrated solid-solution alloy (CSA) compositions under heavy ion irradiation with the goal of evaluating mechanisms for CSA radiation tolerance in advanced fission systems. Three such alloys, Cr18Fe27Mn27Ni28, Cr15Fe35Mn15Ni35, and equimolar NbTaTiV, along with reference materials (pure Ni and E90 for the CrFeMnNi family and pure V for NbTaTiV) were irradiated at 50 K and 773 K with 1 MeV Kr++ ions to various levels of displacements per atom (dpa) using in-situ transmission electron microscopy. Cryogenic irradiation resulted in small defect clusters and faulted dislocation loops as large as 12 nm in face-centered cubic (FCC) CSAs. With thermal diffusion suppressed at cryogenic temperatures, defect densities were lower in all CSAs than in their less compositionally complex reference materials indicating that point defect production is reduced during the displacement cascade stage. High temperature irradiation of the two FCC CSA resulted in the formation of interstitial dislocation loops which by 2 dpa grew to an average size of 27 nm in Cr18Fe27Mn27Ni28 and 10 nm in Cr15Fe35Mn15Ni35. This difference in loop growth kinetics was attributed to the difference in Mn-content due to its effect on the nucleation rate by increasing vacancy mobility or reducing the stacking-fault energy.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Modeling of irradiation-induced microstructure evolution in Fe: Impact of Frenkel pair distribution

Ebrahim Mansouri,Pär Olsson

DOI: https://doi.org/10.1016/j.commatsci.2024.112852

IF: 3.572

2024-02-13

Computational Materials Science

Abstract:This study investigated the irradiation-induced microstructure evolution in Fe, employing the Creation-Relaxation Algorithm and different interatomic potentials. The influence of self-interstitial atoms (SIAs), which were either locally or uniformly being distributed during the creation of the Frenkel pairs, was investigated on the evolving microstructure. The spatially localized distribution of SIAs, mimicking the low-energy transfer irradiation conditions, moderated the microstructure development, compared to uniform distribution of SIAs, delaying the nucleation of dislocation for higher irradiation doses. Introducing multiple Frenkel pairs facilitated a cumulative irradiation dose of 5 dpa in large supercells. In small supercells, the accumulation of SIAs led to the formation of an artificially stabilized self-interacting planar interstitial cluster, suggesting a minimum cell dimension of 10 nm for an accurate modeling of microstructure evolution when the development of the dislocation network is of interest. The formation and evolution of the C15 Laves phase structure were explored. The evolving C15 structure developed larger clusters with uniformly distributed SIAs, and their sizes depended on the interatomic potential employed. Finally, a comparison with experimental measurements demonstrated that the density and the average size of interstitial dislocation loops aligned well with those observed in experimentally irradiated ultra-high purity Fe at low and room temperatures.

materials science, multidisciplinary
Role of Ni, Si and P on the formation of solute-rich clusters under irradiation in Fe-Cr alloys

P.M. Gueye,B. Gómez-Ferrer,C. Kaden,C. Pareige

DOI: https://doi.org/10.1016/j.jnucmat.2022.153958

2022-08-24

Abstract:After irradiation of Fe-Cr alloys of low purity (model alloys of F-M steels), minor solute elements as P, Ni and Si have been shown to create solute clusters which significantly contribute to hardening and might be associated with small dislocation loops. In order to understand the role of each impurity on the formation of the nano-features formed under irradiation and the eventual synergies between the different species, Fe-15at.%Cr-X (X=Si, Ni, P, NiSiP) alloys of different composition have been ion irradiated and characterized using atom probe tomography. Irradiation were performed at 300 {\textdegree}C up to 2.5 dpa in four alloys: Fe15CrNi, Fe15CrSi, Fe15CrP and Fe15CrNiSiP. Influence of C atoms implanted during irradiation on the nanostructure evolution is also discussed. The study of the evolution of the nanofeatures formed under irradiation with the dose as a function of the composition highlights the role of P and C on the formation of the nano-clusters and confirm the radiation-induced nature of solute-rich clusters.

Materials Science

[Problems of diagnosis in chronic pyelonephritis].

A Col E1 hybrid plasmid containing Escherichia coli genes complementing d-xylose negative mutants of Escherichia coli and Salmonella typhimurium.

Microstructure evolution in a Fe-Ni-Si alloy during heat treatment and electron irradiation

Direct Observation of Defect Range and Evolution in Ion-Irradiated Single Crystalline Ni and Ni Binary Alloys

Formation of helical dislocations mediated by interstitials in ion irradiated FeCrAl alloy

Self-ion Irradiation Response of (cocrfeni)94ti2al4 Alloy Containing Coherent Nanoprecipitates

The Effect of Dislocations on MnNi-rich Clusters in Self-Ion Irradiated FeMnNi Alloy

Effect of Carbon on Dislocation Loops Formation during Self-Ion Irradiation in Fe-Cr Alloys at High Temperatures

Deuterium Ion Irradiation Induced Precipitation in Fe–Cr Alloy: Characterization and Effects on Irradiation Behavior

Deformation Localisation in Ion-Irradiated FeCr

Observations of Percolation Structures Induced in Thin Solid Films by Ion Irradiation

Observations of Fractal Patterns Induced in Thin Solid Films by Ion Irradiation.

In Situ Transmission Electron Microscopy Study of Growth of Dislocation Loops in Fe-Ni Alloy under Ion Irradiation

Radiation-induced softening of Fe and Fe-based alloys during in-situ electron irradiation under mechanical testing

Characterising Ion-Irradiated FeCr: Hardness, Thermal Diffusivity and Lattice Strain

Deformation Behaviour of Ion-Irradiated FeCr: A Nanoindentation Study

Dose and compositional dependence of irradiation-induced property change in FeCr

In situ microstructural evolution in face-centered and body-centered cubic complex concentrated solid-solution alloys under heavy ion irradiation

Modeling of irradiation-induced microstructure evolution in Fe: Impact of Frenkel pair distribution

Role of Ni, Si and P on the formation of solute-rich clusters under irradiation in Fe-Cr alloys