Abstract:The formation of large surface grains known as peripheral coarse grains (PCG) is an undesirable feature commonly observed in extruded medium-strength Al-Mg-Si alloys produced for many applications including automotive. The objective of this study was to evaluate factors contributing to the formation of PCG layers, particularly the die bearing geometry, with the goal of developing strategies to eliminate or reduce this phenomenon. This was accomplished using a combination of extrusion trials and finite element method simulations to characterize the role of die bearing geometry on the formation of surface microstructure during the extrusion of an Al-Mg-Si-Mn alloy. The extrusion trials were conducted using two die bearing geometries, (i) a zero bearing die and (ii) a choke die using an extrusion temperature of 480 °C and ram velocities of 20 to 30 mm/s. Axisymmetric extrusion was conducted with an extrusion ratio of 16.5. During the extrusion trials, partially extruded billets were extracted from the extrusion press and water quenched in order to follow the evolution of the surface microstructure for the different bearing geometries. In addition, ram motion was arrested in the middle of the extruded length, held for 5 seconds and then resumed to investigate the role of changing the deformation conditions of the surface on the extruded microstructure. Optical microscopy and electron back-scattered scanning diffraction (EBSD) were used to quantify the microstructure and crystallographic texture of the extrudates and partially extruded billets at different spatial locations. A finite element (FE) mathematical model using the commercial software package DEFORM 2D was also developed to simulate the extrusion process so that loads, temperatures, and material flow patterns could be predicted. The FE model was used to track material flow streamlines close to the surface. Specific locations along these streamlines were then selected for EBSD analysis on the partially extruded billets. The results indicate that the major factor affecting the formation of the PCG layer is the local stored energy of the near surface material which in turn is a function of the details of the die bearing geometry.

Experimental investigation and numerical prediction of the peripheral coarse grain (PCG) evolution during the extrusion of different AA6082 aluminum alloy profiles.

Numerical investigation of the surface recrystallization during the extrusion of a AA6082 aluminum alloy under different process conditions

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

The Effect of Die Bearing Geometry on Surface Recrystallization During Extrusion of an Al-Mg-Si-Mn Alloy

Numerical, experimental, and analytical investigation of the skin contamination evolution in the extrusion of different industrial profiles

FEM Validation of Front End and Back End Defects Evolution in AA6063 and AA6082 Aluminum Alloys Profiles

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Microstructural Evolution in a 6060 Extrudable Al-Alloy: Integrated Modeling and Experimental Validation

Microstructure evolution, constitutive modeling and forming simulation of AA6063 aluminum alloy in hot deformation

Multiscale Mechanical Behavior and Microstructure Evolution of Extruded Magnesium Alloy Sheets: Experimental and Crystal Plasticity Analysis

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

Coupled CA-FE Simulation for Dynamic Recrystallization of Magnesium Alloy During Hot Extrusion

A Study on Peripheral Grain Structure Evolution of an AA7050 Aluminum Alloy with a Laboratory-Scale Extrusion Setup

Comprehensive study of hot compression behaviors and microstructure evolution of solutionized 6082 aluminum alloy extruded bar

A profound study of damage behavior for Al 2024-T3 alloy worksheet produced by constrained groove pressing in the superior practical condition

Optimization of porthole extrusion die for 6063 aluminum alloy profile with thin-walled multi-cavity complex section and analysis of profile performance

Extrusion of 7075 Aluminium Alloy Through Double-Pocket Dies to Manufacture a Complex Profile

Phase Field Method for the Assessment of the New-Old Billet Material Interaction during Continuous Extrusion Using COMSOL Multiphysics

Mechanical response and texture evolution prediction of AZ31 magnesium alloy during CVCDE process using crystal plasticity finite element method

Prediction of microstructure evolution of Al–1% Mg alloy during hot forming and sequential heat treatment

FE Simulation of Extrusion to Produce a Thin-Walled Wide Profile Through a Spreading Pocket Die