Abstract:Microstructure characteristics are important for the high-performance Sm2Co17-type permanent magnets to achieve high intrinsic coercivity (H cj) and large magnetic field at the knee-point (H knee). In this work, the correlation between microstructures and magnetic properties has been systematically studied. The different microstructures were obtained by two procedures: by adjusting the aging temperature and optimizing the Zr content. On one hand, with increase of aging temperature from 1063 K to 1103 K, the cell size and the lamellar phase density increase from 75.1 nm and 0.014 1/nm to 101.5 nm and 0.043 1/nm, respectively, and the average peak Cu concentration at the cell boundaries reaches 21.9 at% which is helpful for obtaining relatively high H cj and H knee. As the aging temperature increases further to 1143 K, a much larger cell size and with incomplete cell boundaries results in an irregular distribution of Cu concentration at the cell boundaries. In this case, the H knee is low even though the magnet shows a high H cj. On the other hand, the increase of Zr content also promotes an increase in both the lamellar phase density and the average peak Cu concentration at the cell boundaries, giving rise to high H cj and H knee. Taking into consideration the aging temperature and Zr content, one can conclude that a lower aging temperature and lower Zr content produce a lower lamellar phase density and average Cu concentration at the cell boundaries and this leads to a lower H cj and H knee of the magnets. To further confirm this correlation between the microstructures and magnetic properties, a magnet of Sm(CobalCu0.062Fe0.285Zr0.016)7.6 was aged at a higher temperature of 1143 K to increase the lamellar phase density. As expected, the lamellar phase density increases from 0.008 to 0.013 1/nm; however, the cell size increases simultaneously from 142.5 to 247 nm. The magnet exhibits a much higher but uneven Cu concentration at the cell boundaries. As a result, the H cj increases from 1.64 to 10.18 kOe, while H knee just increases from 1.09 to 3.91 kOe.

Unveiling the enhancement of mechanical properties in cryogenic-treated Sm 2 Co 17 permanent magnets without sacrifice of magnetic properties

Overcoming mechanical fragility in Sm-Co permanent magnet materials

Microstructural Characterization of Sm-Co Magnets

Effect of post-solutionizing cooling rate on microstructure and magnetic properties of 2:17-type Sm-Co-Fe-Cu-Zr magnets

Improvement of coercivity thermal stability of sintered 2:17 SmCo permanent magnet by Nd doping

Correlation of mechanical anisotropy with fine grain strengthening for Sm2Co17-type sintered permanent magnets

Magnetic Properties Enhancement of Multi-Element-doped SmCo7 Nanocrystalline Alloys

Microstructure characteristics and optimization of 2:17-type Sm-Co sintered magnets with different iron content

Effect of interfacial stress on microchemistry and coercivity in 2:17-type SmCo sintered magnets

Enhanced Magnetic Properties of Fe-rich Sm-Co-Fe-Cu-Zr Magnets by Compressive Stress-Aging

Study on the grain growth and the evolution of defects around grain boundaries during heat treatment process in Sm 2 Co 17 permanent magnets

Coercivity mechanism of high-performance anisotropic heterostructure SmCo 5 magnets

Atomic-scale structure clarification of the planar Z phase and its influence on the magnetic properties in Sm(CoFeCuZr) permanent magnets

Influence of Severe Plastic Deformation on the Magnetic Properties of Sm‐Co Permanent Magnets

Growth of defects around grain boundary and evolution of cellular structure during isothermal aging process in 2:17-type SmCo permanent magnets

Phase separation and chemistry evolution in Fe-rich Sm(CobalFe0.31Cu0.07Zr0.025)7.7 magnets: The effect of initial defect

Dependence of macromagnetic properties on the microstructure in high-performance Sm2Co17-type permanent magnets

Overview of composition and technique process study on 2:17-type Sm–Co high-temperature permanent magnet

Mechanical properties of samarium cobalt: A molecular dynamics study

Shortened Processing Duration of High-Performance Sm-Co-Fe-Cu-Zr Magnets by Stress-Aging

Evolution of phase, texture, microstructure and magnetic properties of Fe-Cr-Co-Mo-Ti permanent magnets