Abstract:Wellbore stability is important to deep-sea drilling (DSD) for exploiting offshore oil and gas resources. Accurate prediction of the mechanical behaviors of rock formation around the wellbore can effectively prevent wellbore failure via adjusting mud weight. In this paper, a fully coupled thermo-poro-elastic (THM) model is developed by combining fluid circulation in the wellbore and rock deformation in the reservoir. Transient heat transfer in the wellbore/reservoir and heat exchange between the tubing, annulus, riser, casing, cement, seawater and rock formation are considered. By decomposing the problem into axisymmetric and antisymmetric sub-problems, the analytical solutions for transient temperature, pressure and stress in the rock formation and fluid temperature changes in the drill pipe, annulus and seawater near the riser are obtained and validated against with the numerical solutions, existing fluid circulation model, field measurement data and the existing model without considering fluid circulation. After that, a typical case study is carried out to show the mechanical behavior around the wellbore. It is found that the proposed fully coupled THM model has a high accuracy with a relative error of around 1.2%. There is a large difference in the predicted bottomhole temperature (BHT) and thus the temperature in the reservoir between the models with and without considering fluid circulation in the wellbore. An assumption of constant temperature boundary condition may lead to overestimated or underestimated results depending on the selection of the assigned wellbore temperature. In the DSD case studied, the rock formation at the upper part of the reservoir (Z < 0.40) is continuously heated and the rock formation at the lower part (Z > 0.6) of the reservoir is continuously cooled during fluid circulation, which thus results in a complex heat transfer and thus mechanical behavior in the wellbore/reservoir system, especially near the wellbore. The bottomhole temperature (BHT) decreases by 38.9 K due to cold fluid circulation from 3.68 min to 25.68 days, which can lead to 14.59 MPa tensile stress that cannot be ignored for wellbore stability analysis. The proposed analytical model provides a useful tool to predict the mechanical behaviors such as the transient temperature, pressure, displacement and stresses in the wellbore/reservoir system during fluid circulation in DSD. It runs efficiently in terms of seconds per case study in a portable laptop computer and can also work a benchmark for other numerical methods. However, the fully coupled THM model and its analytical solution are based on several assumptions, such as the heat generated by the drill bit rotation is ignored and only the liquid phase is considered, which requires further investigation.

A new two-dimensional transient forecast model of wellbore temperature based on precise time step integration method

An improved thermal model for predicting wellbore temperature distribution in deep-water gas well

Temperature Prediction of Geothermal Drilling Considering the Drilling Fluid Thermophysical Parameters

Transient prediction method for flow temperature at wellbore bottom

Wellbore Temperature Field Prediction in Marine Drilling

A Transient Analytical Model for Predicting Wellbore/Reservoir Temperature and Stresses during Drilling with Fluid Circulation

A Fully Coupled Thermo-Poro-elastic Model Predicting the Stability of Wellbore in Deep-Sea Drilling. Part A: Analytic Solutions

A Coupled Model of Two-Phase Fluid Flow and Heat Transfer to Transient Temperature Distribution and Seepage Characteristics for Water-Flooding Production Well with Multiple Pay Zones

Numerical analysis of heat transfer rate and wellbore temperature distribution under different circulating modes of Reel-well drilling

Fully transient coupled prediction model of wellbore temperature and pressure for multi-phase flow during underbalanced drilling

A novel analytical transient heat-conduction time function for heat transfer in steam injection wells considering the wellbore heat capacity

A Transient Thermal Model for Forecasting the Real-Time Temperature of Downhole Electronics

High Precision Approximate Solution of Transient Heat-Conduction Time Function of Wellbore Heat Transfer

2D Transient Simulation of Conjugate Natural Convection and Radiation Within Thermal Wellbore Annuli

A Novel Geothermal Wellbore Model Based on the Drift-Flux Approach

Numerical simulation of fracture temperature field distribution during oil and gas reservoir hydraulic fracturing based on unsteady wellbore temperature field model

A prediction model of wellbore temperature and pressure distribution in hydrocarbon gas injection well

Transient Heat Transfer Model for Wellbore and Formation of Shut-In Offshore Oil Wells

Wellbore Temperature and Pressure Field in Deep-water Drilling and the Applications in Prediction of Hydrate Formation Region

Computational Fluid Dynamics Modeling and Analysis of Axial and Radial Temperature of Wellbore during Injection and Production Process

A Novel Prediction Model for Steam Temperature Field of Downhole Multi-Thermal Fluid Generator