Abstract:Molten-Salt Reactors (MSRs) use molten-salt fluid-fuel, which contains thorium (Th) and uranium-233 (233U) as fertile and fissile, respectively. Also, the MSRs can accept plutonium (Pu) as fissile. Besides the above benefit on nuclear fuel cycle, the MSR has other many advantages such as the power-size flexibility, no necessity of refueling, effective incineration of minor actinides (MA), excellent safety, and good economy. The cycle produces very small amount of MA compared with the conventional U fuel cycle. Also, 233U accompanies high gamma-ray emissions, and this fact contributes to the resistance to nuclear proliferation issues. The MSRs has been studied since early 1950's in Oak Ridge National Laboratory (ORNL), and the Molten-Salt test Reactor Experiment (MSRE) has shown excellent operation in 1965-69. The conceptual design study was issued for Molten-Salt Breeder Reactor (MSBR) as large as 1GWe plant. In Japan, small MSRs of 150MWe to 200MWe(FUJI-, FUJI-12 and FUJI-U3) have been proposed. FUJI-12 is a simple one-region core, and it attained a high conversion ratio of 0.92 by the batch chemical processing at every 7.5 years. However, FUJI-12 has to replace the graphite moderator at every 15 years, and this may cause additional maintenance work and cost. Then, an improved small MSR (FUJI-U3) has been proposed. The improvement is to introduce a 3-region core design concept in order to eliminate graphite replacement by reducing the maximum neutron flux. It is concluded that there is no need to replace graphite moderator for 30 years operation of FUJI-U3. In this paper, we investigated the other possibility of a two region core for the simplicity. Using one energy group neutron diffusion theory and assuming bare reactor, the optimum selection of region wise neutron multiplication factors can be theoretically and easily obtained. The validity of the selection was also proved by a numerical calculation. In MSRs, there is no burnup distribution of the fuel. The region wise neutron multiplications can be obtained by adjusting the volume fraction of fuel in a cell with a given composition of fuel salt. Thus, it is easy to apply the theoretical result directly in selecting the boundary of the region and the multiplication factor in each region and also to maintain the characteristics during the core burnup. The optimization of the actual core configuration was searched by a nuclear analysis code SRAC95 with the nuclear data library of JENDL3.2. In such case the region wise multiplication factor can be adjusted to compensate the neutron loss by leakage in order to attain criticality. Taking the theoretical result as the initial condition, the optimization was quite easy to accomplish. It is concluded that there is no need to replace graphite moderator for 33 years operation of a two-region core design concept.

Safety Enhancement in the Molten Salt Fast Reactor (MSFR)

CFD Simulations of the Molten Salt Fast Reactor

Preliminary Analysis and Design of the Energy Conversion System for the Molten Salt Fast Reactor

Core and blanket thermal–hydraulic analysis of a molten salt fast reactor based on coupling of OpenMC and OpenFOAM

Core calculations of the Molten Salt Fast Reactor using different computational codes

The neutronic characteristics of thermal molten salt reactor

On the Employment of a Chloride or Fluoride Salt Fuel System in Advanced Molten Salt Reactors, Part 1: Thermophysical Properties and Core Criticality

Analysis of the thermal feedback effect and nuclides flow effect on the fuel‐cycle characteristics of Molten Salt Reactors

CFD simulations of Molten Salt Fast Reactor core cavity flows

Studies on Flibe Blanket Designs in Helical Reactor FFHR

Mitigation of the Local Overheating Phenomenon in Molten Salt Electric Heaters Through Flow Field Optimization

Design studies for A 50 MWth molten salt fast reactor

Design study of heat transport and power conversion systems for micro molten salt reactor

Possible Configurations for the Thorium Molten Salt Reactor and Advantages of the Fast Nonmoderated Version

ICONE19-43445 Investigating Thermal-Hydraulic Characteristic of Molten Fluoride Salt in A Circular Pipe Using A CFD Methodology

[ICAPP 2023] A burnable absorber design study for a Passively-Cooled Molten Salt Fast Reactor

Preliminary Study on the Candidate Fuel Salt of Molten Chloride Salt Fast Reactor

A Consistent One-Dimensional Multigroup Diffusion Model for Molten Salt Reactor Neutronics Calculations

Thermal Hydraulics Analysis of the Fluoride-Salt-Cooled, High-Temperature Reactor

On the Use of a Chloride or Fluoride Salt Fuel System in Advanced Molten Salt Reactors, Part 3; Radiation Damage

Flattening of Fast Neutron Flux Distribution in Molten Salt Reactor for Longer Graphite Moderator Lifetime