Abstract:Optical glasses used in a range of industrially important optoelectronic devices must be polished to nano-level roughness for proper device operation. Polishing process with magnetic compound fluid slurry (MCF polishing) under a rotary magnetic field is an influential candidate for the method to precisely polish optical glass. MCF slurry has been successfully utilized to polish a variety of materials, ranging from soft optical polymers to hard optical glasses. MCF was developed by mixing a magnetic fluid and a magnetorheological fluid with the same base solvent, and hence includes not only μm-sized iron particles but also nm-sized magnetite particles. To elucidate the behaviour of material removal in MCF polishing, this study measured the normal and shear forces generated in the polishing zone during polishing. From these measurements, the distributions of pressure P and shear stress τ were obtained. The distribution of material removal rate (MRR) was investigated through spot polishing of borosilicate glass. The effects of three process parameters, namely magnet revolution speed, MCF carrier rotational speed and working gap, on pressure P, shear stress τ and the MRR were also investigated. The results revealed that P is higher near the centre of the interacting area (i.e. the polishing spot centre) and the point of maximum shear stress τ appears at about 5mm from the polishing spot centre. All of P, τ and MRR are sensitive to MCF carrier rotational speed and working gap but insensitive to magnet revolution speed. Shear stress is more sensitive to these process parameters than the pressure. Cross-sectional profiles of the polishing spots exhibit a characteristic symmetric W-shape; material removals are minimal at the spot centre and maximal at approximately 8.2–10.2mm from the spot centre depending on the process parameters. MRR is proportional to the MCF carrier rotational speed and is negatively correlated with working gap. An MRR model involving both the pressure and shear stress in MCF polishing is proposed. In the model, MRR is more dominated by shear stress than by pressure.

Analysis of Surface Roughness during Surface Polishing of ITO Thin Film Using Acoustic Emission Sensor Monitoring

Nano-Precision Synergistic Finishing Process Integrated ELID-Grinding and MRF

Incined Magnetorheological Finishing and Its Path Controlling

Active Control of Surface Integrity in Thin Film Scratching and Finishing

Application of surface analysis in study on removal mechanism and abrasive selection during fused silica chemical mechanical polishing

Electrochemical Analysis of the Slurry Composition for Chemical Mechanical Polishing of Flexible Stainless-Steel Substrates

Machining Characteristics of Electrochemical Polishing Using Ultrasonic Vibration for Nanoscale High Surface Quality.

Planar Oscillation-Enabled Deterministic Magnetorheological Micro-Polishing

An in Situ End-Point Detection System Using Motor Power Signal for Chemical Mechanical Planarization Process

Experimental Study on the Effects of Alumina Abrasive Particle Behavior in MR Polishing for MEMS Applications

Effects of Pressure and Shear Stress on Material Removal Rate in Ultra-Fine Polishing of Optical Glass with Magnetic Compound Fluid Slurry

Surface Morphology Evolution during Chemical Mechanical Polishing Based on Microscale Material Removal Modeling for Monocrystalline Silicon

Subsurface Damage Detection And Damage Mechanism Analysis Of Chemical-Mechanical Polished Optics

Study on Process Optimization of Ultrasound Assisted Magneto-Rheological Polishing of Sapphire Hemisphere Surface Based on Fe3O4/SiO2 Core-Shell Abrasives

The Deterioration Characteristics and Mechanism of Polishing Pads in Chemical Mechanical Polishing of Fused Silica

The generation mechanism and suppression method of the "comet tail" defect on the single-crystal silicon surface polishing with magnetorheological

Motor Power Signal Analysis for End-Point Detection of Chemical Mechanical Planarization

Investigation on the Polishing of Aspheric Surfaces with a Doughnut-Shaped Magnetic Compound Fluid (MCF) Tool Using an Industrial Robot

Surface Roughness and Material-Removal Rate with Magnetorheological Finishing Without Subsurface Damage of the Surface

Endpoint Detection Based on Optical Method in Chemical Mechanical Polishing

The polishing mechanism of electrochemical mechanical polishing technology