Abstract:Thermal interface materials (TIMs) are indispensable materials in thermal management, and Al2O3-based TIMs are most widely used in thermal managements. Surface modification is an effective method to improve Al2O3 dispersion in matrix, thereby increasing the maximum filler loading. However, traditional surfactants hardly promote the interfacial heat-transfer on the premise of the same filler loading. In this work, we proposed an electrostatic self-assembly strategy to functionalize the surface of Al2O3 particles with MXene sheets to enhance the interfacial heat-transfer between fillers and silicone rubber (SR). To validate the effectiveness of MXene, we compared the Al2O3-MXene-SR TIM with Al2O3-graphene-SR TIM and Al2O3-SR TIM under the same Al2O3 loading in the aspects of mechanical properties and thermal properties. Though MXene could increase the viscosity and hardness, the negative influence of MXene is much weaker than that of graphene. Nevertheless, the positive impact of MXene is more significant. First, it can reinforce the mechanical strength. The experiment showed the breaking tensile strength of the Al2O3-MXene-SR TIM is 0.117 MPa, higher than that of the Al2O3-graphene-SR TIM (0.082 MPa) and the Al2O3-SR TIM (0.07 MPa). Second, the thermal conductivity of TIMs improves a lot after MXene coating. The thermal conductivity of Al2O3-MXene-SR TIM is 3.4 W·m−1·K−1, with the matrix/filler mass ratio of 100:1600, which is 30% higher than that of the Al2O3-SR TIM (2.6 W·m−1·K−1) and 21% higher than that of Al2O3-Gr-SR TIM (2.8 W·m−1·K−1). Whereas the Al2O3 loading keeps the same and the MXene fraction is only about 1.16 vol‰, the increment of the thermal conductivity is mostly due to the improvement of interfacial heat-transfer via MXene. The temperature cycling test and aging test implied that the Al2O3-MXene-SR TIM is thermally stable and reliable. The underlying mechanism of the interfacial heat-transfer enhancement was revealed by the analysis of phonon density of states (PDOS) via a molecular dynamics simulation. The PDOS of MXene is more compatible with Al2O3 and SR than graphene, so MXene sheets play the role as a bridge between Al2O3 and SR to improve the interfacial phonon transport. This work provides an effective method to reduce interfacial thermal resistance in TIMs, which could facilitate the development of thermal management materials.

The improved thermal conductivity and heat dissipation capacity of elastomer‐based thermal interface materials through promoting the surface interactions and complete networks

Low Interfacial Thermal Resistance Between Crossed Ultra-Thin Carbon Nanothreads

The polymer-based thermal interface materials with improved thermal conductivity, compression resilience, and electromagnetic interference shielding performance by introducing uniformly melamine foam

Interacted boron nitride/Mxene hybrids with vertically aligned networks for improving the thermal conductivity, electromagnetic wave absorption and mechanical properties for the polymer-based thermal interface materials

Graphene-Assisted Thermal Interface Materials with a Satisfied Interface Contact Level Between the Matrix and Fillers

Enhancement of thermal conductivity and insulation of silicone thermal interface material through surface modification and synergistic effects of nanofillers for thermal management of electronic devices

Reduced Graphene Oxide Embedded with MQ Silicone Resin Nano-Aggregates for Silicone Rubber Composites with Enhanced Thermal Conductivity and Mechanical Performance

Graphene/Polyolefin Elastomer Films as Thermal Interface Materials with High Thermal Conductivity, Flexibility, and Good Adhesion

Controllable Ag-rGO Heterostructure for Highly Thermal Conductivity in Layer-by-layer Nanocellulose Hybrid Films

Paving 3D interconnected Cring-C3N4@rGO skeleton for polymer composites with efficient thermal management performance yet high electrical insulation

Enhanced interfacial heat-transfer of Al2O3-MXene-silicone composite via an electrostatic self-assembly strategy

RGO/TPU Composite with a Segregated Structure As Thermal Interface Material

Micro-diamond assisted bidirectional tuning of thermal conductivity in multifunctional graphene nanoplatelets/nanofibrillated cellulose films

Synergistic Enhanced Thermal Conductivity of Polydimethylsiloxane Composites Via Introducing SCF and Hetero-Structured GB@rGO Hybrid Fillers

High damping, soft and reprocessable thermal interface materials inspired by the microstructure of skin tissue

Highly conductive thermal interface materials with vertically aligned graphite-nanoplatelet filler towards: High power density electronic device cooling

Liquid metal incorporated graphene oxide films with enhanced through-plane thermal conductivity and flame resistance

Environment-adaptive, anti-fatigue thermal interface graphene foam

Interface Phonon Scattering Suppression Boosts Heat Conduction in Thermal Interface Materials

Highly Thermally Conductive Flexible Insulated PI/BNNS@rGO Nanocomposite Paper with a Three-Dimensional Network Bridge Structure

Promoting Thermal Conductivity of Alumina-Based Composite Materials by Systematically Incorporating Modified Graphene Oxide