Abstract:International emission tests (EPA, SFTP, MVEG-B, J-10.15, etc.) are carried out with vehicles running on the rolls dynamometer. Results, in terms of total emissions, are influenced by vehicles parameters such as mass, gear ratios, front surface, drag coefficient, etc. It would be useful, in the automobiles design phase, to have information about the impact of these parameters on total emissions. The obvious solution would be to build up a complete vehicle model to simulate performance and emission levels. Engine pollutants production modeling is the weak point, since it is difficult to obtain reliable results. Anyway it is possible to avoid pollutants production simulation, testing the actual engine under the same operating condition it would face inside the car’s hood. This paper describes a methodology whose aim is to test the engine on a standard test bench, simulating on-board operating conditions. An equivalence condition has to be satisfied in order to guarantee the methodology effectiveness: engine speed and Manifold Absolute Pressure (MAP) must always match for the two types of test performed on the same driving cycle. Engine speed and torque can be controlled through the bench actuators, their values depending on the simulated vehicle motion: once the car dynamics are simulated by means of a model, engine speed and torque corresponding to the given driving cycle can in fact be evaluated. The model is solved in real time, its output being the brake load torque value satisfying the equivalence condition. The brake controller, used as a slave, regulates the engine operating conditions consequently. The global model incorporates tires, aerodynamic forces, clutch, gearbox and driveline behaviors simulation: its response has been first validated comparing its outputs with data measured on board, and then it has been used to control an eddy current brake, for vehicle test simulation on the test bench. Two different control philosophies can be used: either a human driver or an automatic controller can ride the simulated car. The influence of vehicle parameters and gearshift mode on fuel consumption and pollutant emissions can be investigated.

Emission Reduction from a Light-Duty Diesel Vehicle over Two Driving Cycles through Dynamic Correction Calibration

Investigation of an efficient model-based fuel economy optimization methodology for diesel engines focusing on real world driving emission cycles

Study on Control Strategies on NO X Emissions to Meet Real Driving Emissions

Model-Based Calibration and Control of Tailpipe Nitrogen Oxide Emissions in a Light-Duty Diesel Engine and Its Assessment through Model-In-The-Loop

Intelligent Transient Calibration of a Dual-Loop EGR Diesel Engine Using Chaos-Enhanced Accelerated Particle Swarm Optimization Algorithm

Nonlinear Model Predictive Control of Integrated Diesel Engine and Selective Catalytic Reduction System for Simultaneous Fuel Economy Improvement and Emissions Reduction

Improvement of the light-load combustion control strategy for a heavy-duty diesel engine fueled with diesel/methonal by RSM-NSGA III

Using a Chassis Dynamometer to Determine the Influencing Factors for the Emissions of Euro VI Vehicles

Application of CFD, Taguchi Method, and ANOVA Technique to Optimize Combustion and Emissions in a Light Duty Diesel Engine

Development and Validation of a Modeling and Calibration Method for Diesel-Like Multistage Combustion Based On a Modified Multi-Wiebe Function

Research on cross sensitivity of NOx sensor and Adblue injection volume in accordance with the actual situation based on cubature Kalman filter

Model predictive emissions control of a diesel engine airpath: Design and experimental evaluation

Experimental Assessment of NOx Emissions from 73 Euro 6 Diesel Passenger Cars

Fuel consumption and emission performance from light-duty conventional/hybrid-electric vehicles over different cycles and real driving tests

On-Board Sensor-Based NO x Emissions from Heavy-Duty Diesel Vehicles

Emission rates of regulated pollutants from current technology heavy-duty diesel and natural gas goods movement vehicles

Optimization of the ammonia coverage ratio references in diesel engine two-can selective catalytic reduction systems via nonlinear model predictive control

Model-based Calibration for the Control Variables of an Atkinson Cycle Engine

Experimental Study and Model Predictive Control of a Lean-Burn Gasoline Engine Coupled With a Passive Selective Catalytic Reduction System

Vehicle Simulation on the Test Bench

Steady Condition Calibration of Turbocharged Lean Burn HCNG Engine