Abstract:Neutronic, thermal-hydraulics, and solid mechanics computations were used to study the different VVER-1000 reactors' operational conditions for the steady-state and the transient state. The main objective of these studies is to investigate the safe operating conditions, which is essential in determining the reactor safety limits. The coupling between different physics enables a better understanding of reactor phenomena and enhanced accuracy by reducing the assumption needed for separate calculations for different physics. MCNPX code is used to provide the source power distribution for two themes of calculations. The first theme is the analytical solution using MATLAB software, and the second theme is the finite element coupled physics using COMSOL Multiphysics. Analytical solutions using MATLAB software and results from COMSOL-Multiphysics were used to simulate the uncoupled analytical models and coupled models, respectively. The coupled theme provide feedbacks between different physics by iterating the solution between different physics; such as solving the heat transfer with taking into consideration the variation of the coolant velocity along the coolant channel and solving solid mechanics with taking into consideration the change of either the fuel and the clad temperatures distribution (thermal load) or the change in the coolant pressure (pressure load). While in the uncoupled solutions, certain assumptions reflect an average behavior for the effect of other physics on the physics under concern, such as the average pressure of the coolant and the average value for the coolant velocity. The obtained results are verified by comparing it to WIMS D-4 for neutronic calculations and COPERA-EN code for the thermal-hydraulic analytical solution. Also, thermal-hydraulic results by both coupled and uncoupled themes are verified against results from the final safety analysis report. The Departure from Nucleate Boiling Ratio (DNBR) and the Minimum Departure from Nucleate Boiling Ratio (MDNBR) were applied for the investigation of VVER-1000 reactor safety parameters. Solid mechanics, fluid dynamics and heat transfer were used to compute the maximum stress/maximum volumetric strain acting on both fuel and cladding material. Results from both methods satisfied the limits addressed by the designer and shows a good agreement with the other published works that used WIMS D-4 for neutronic calculations and COBRA-EN code for thermal-hydraulic calculations analytically. in addition, the maximum stress occurring on the fuel and clad materials didn't exceed the yield stress. Furthermore, the fuel material displacement didn't exceed the Helium gap thickness, which means the surface contact between the fuel and the clad material is impossible that prevents the chemical interaction between both fuel and clad at 1135 K.

Investigation of the influence of the fuel element design parameter on the VVER-1000 reactor axial power peaking factor

Study on neutronic behavior of VVER-1000 fuel assembly with duplex fuel rod design

Particle emission from irradiated VVER-1200 fuel with Am burnable absorber

ANALYSIS OF UO2-BEO FUEL PERFORMANCE DURING NORMAL CONDITIONS AND RIA

Conceptual design and analysis of a new plate-type fuel element for flattening of reactor power distribution

Non-uniform fuel distribution and thermo-mechanical analysis of a 1 MW thermal power micronuclear heat pipe reactor

Investigation of the Thermal Effects of MgO and ZnO Nanoparticles in a Pressurized Water Reactor Coolant with Computational Fluid Dynamics Model

Neutronic Study of UO2-BeO Fuel with Various Claddings

Calculation of Fuel Rod Strength Under Steady-State Operating Condition

A method for design a linear heat rate ramp limit curve for thermal reactor fuel rods

Neutronic analysis of new generation TVS-2M fuel assemblies in VVER-1000 reactor type

Comparison of the neutronic properties of the (Th- 233 U)O 2 , (Th- 233 U)C, and (Th- 233 U)N fuels in small long-life PWR cores with 300, 400, and 500 MW th of power

Thermal-Hydraulic Design of High-Power-Density Annular Fuel in PWRs

Thermal-hydraulic and solid mechanics safety analysis for VVER-1000 reactor using analytical and CFD approaches

Evaluation of neutronic parameters for RITM-200 reactor unit considering (238U+235U)O2, (232Th+235U)O2 and (232Th+233U)O2 dispersed fuel using MCU-PTR

Design and Evaluation of a High Power Density and High Energy Efficiency Fuel Element for Space Nuclear Reactors

Impact of High Porosity on Thermal Transport in UO_2 Nuclear Fuel

Design research for the porous hexagonal prism shaped fuel element adopted in nuclear thermal propulsion reactor based on neutronics and thermal-hydraulics coupled method

Three-dimensional FE analysis of the thermal-mechanical behaviors in the nuclear fuel rods

Study on physics characteristics of Th-U fuel in long-cycle core

Neutronics Analysis of VVER-1000 Core Using At-Fcm Fuel

﻿Investigation of the influence of the fuel element design parameter on the VVER-1000 reactor axial power peaking factor