Abstract:_ This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper SPE 212443, “Real-Time Anomaly-Detection Methodology for Drilling-Fluid Properties,” by Moacyr N.B. Filho, Thalles P. Mello, and Cláudia M. Scheid, Federal Rural University of Rio de Janeiro, et al. The paper has not been peer reviewed. _ Online drilling-fluid-measurement technologies have become an essential tool for drilling automation. While online density measurements are widespread, the availability of rheology measurements is increasing quickly, and additional properties are central to ongoing field trials. The complete paper presents the concept of supervisory and advisory systems dedicated to support the detection of abnormal events and to provide guidelines for fluid treatment. Introduction The Laboratory of Fluid Flow of the Federal Rural University of Rio de Janeiro and Petrobras developed a flow loop for the proposal and validation of online sensors for the measurement of drilling-fluid properties. In previous work, the authors described the development of a set of online sensors to measure fluid properties with control of operational conditions of temperature, pressure, and fluid flow rate. Following previous research, this study proposes a new method using a technique based purely on data to diagnose and detect deviations in drilling-fluid properties. The method proposed applies principal component analysis (PCA) for detecting anomalies in drilling fluids. Method PCA-Based Anomaly-Detection Technique. This method consists of the linear transformation of the space of monitored variables, which generates a new space of variables called principal components, in which each principal component is a linear combination of the process variable. This allows the new space of variables to be linearly independent—that is, the principal components are linearly independent, allowing the calculation of process monitoring statistics. The ability to detect anomalies in drilling-fluid properties is necessary to train the system in the normal state of operation. The training based on the normal state of operation was performed through the calculation of the principal-component matrix and the selection of the reduced principal-component matrix. Once the process model was trained, the monitoring of new samples was performed with the help of two statistical tools that described the health of the process operation: T2 and Q statistics. The T2 statistic measures variations in the main space. T2 only detects variation in the subspace of the first principal components larger than those attributed to the dynamics of the process. The Q statistic denotes the change of events not explained by the principal-component model. It is a measure of the difference, or residual, between a sample and its projection on the model. The failure-detection procedure based on the use of PCA consisted of continuous assessments of whether process statistics were within or outside an acceptable range. A method previously proposed in the literature used control systems based on fuzzy logic to monitor properties of drilling fluids and propose corrections, which are performed automatically by an experimental unit containing actuators for additions of drilling agents as thickeners and viscosifiers. The application of fuzzy logic depends on inference rules, which must be provided to the system by the programmer. This is a limitation of corrective systems based on fuzzy logic.

The Monitoring of Abnormal Fluid Properties Based on PCA Technique as an Alternative Strategy to Support Autonomous Drilling Operations

Method Provides Real-Time Anomaly Detection for Drilling-Fluid Properties

Dynamic PCA-based Fault Detection and Diagnosis Analysis

PCA-based Fault Detection and Diagnosis with Application to Heavy Oil Fractionator

Process monitoring and fault detection based on multivariate statistical projection analysis

Chemical Process Monitoring and Fault Diagnosis Based on Independent Component Analysis

Fuzzy-Based Control System of Drilling Fluids Density and Apparent Viscosity Simultaneously: An Alternative Strategy to Support Autonomous Drilling Operations

Distributed Monitoring With Integrated Probability PCA and mRMR for Drilling Processes

Primary-Auxiliary Statistical Local Kernel Principal Component Analysis and Its Application to Incipient Fault Detection of Nonlinear Industrial Processes

Petroleum well drilling monitoring through cutting image analysis and artificial intelligence techniques

Six Years Operating a Real Time Drilling Problem Detection Software in Deepwater Environments: Results and Challenges

A Recursively Updated Map-Reduce Based PCA for Monitoring the Time-Varying Fluorochemical Engineering Processes with Big Data

Fault detection method based on kernel principal angle

Fault Detection Behavior And Performance Analysis Of Principal Component Analysis Based Process Monitoring Methods

DRKPCA-VBGMM: fault monitoring via dynamically-recursive kernel principal component analysis with variational Bayesian Gaussian mixture model

Development of Online Drilling Fluid Property Logging System

Use of Machine Learning and Data Analytics to Detect Downhole Abnormalities While Drilling Horizontal Wells, With Real Case Study

A data-driven pipeline pressure procedure for remote monitoring of centrifugal pumps

The development and application of an intelligent detection and evaluation system for drilling fluid

Fault monitoring using novel adaptive kernel principal component analysis integrating grey relational analysis

Simultaneous Fault Detection and Diagnosis Using Adaptive Principal Component Analysis and Multivariate Contribution Analysis