Abstract:Nowadays, pumps of different size are needed for a great variety of purposes. In the past, both computational fluid dynamics (CFD) and experimental flow visualization were performed to reveal flow characteristics within centrifugal pumps, to examine a specific design and to guide design improvement (see Burgreen et al. 1996, 2000). Li et al. (2007) studied the interior viscous flow in a mini pump with an asymmetric axis using CFD and PIV (particle image velocimetry) for improvement of the pump design. Matsui et al. (2002) adopted the the k-ω model in the CFD simulation for a centrfugal pump, and the computational grid system only consisted of one flow passage for LDV (laser Dopler velocimetry) test impeller. Byskov et al. (2003a) and Pedersen & Larsen (2003 b) investigated the flow inside the rotating passages of a six-bladed shrouded centrifugal pump impeller using LES simulation and PIV and LDV measurements. The velocities predicted with LES were in good agreement with the experimental data. The two RANS simulations were, however, not able to predict this complex flow field. It was thus found that using LES for analyzing the flow field in centrifugal pumps could shed light on basic fluid dynamic with a satisfactory accuracy compared to experiments. A transient simulation was used to study the effects of pulsatile blood flow due to the heartbeat through blood pumps by Song et al. (2003). The microsized geometry of the pump made the choice of turbulence models significant for the accuracy of calculation. The comparison showed that the k-ω model gave better predictions of the shear level within the near wall regions than the k-e model. Guleren and Pinarbasi (2004) indicated that the stallcell size extended from one to two diffuser passages. Comparisons of the computational results with experimental data were made and showed good agreement. The unsteady flow in a low specific speed radial diffuser was simulated by the CFD code CFX-10 by Feng et al. (2009). The PIV and LDV measurements had been conducted to validate the CFD results. Both the phase-averaged velocity fields and the turbulence fields obtained from different methods are presented and compared. In this study, in order to get more information about the internal flow of a centrifugal pump, both experimental measurement and numerical simulation are engaged. A centrifugal model pump test rig is built for PIV measurement. The test, involving the technology of index match and fluorescent, is for acquiring flow pattern in a fixed rotational speed, the velocity distribution of the flow field are thus obtained. And, the RANS (Reynolds

Investigation of Turbulence Modeling in a High Speed Centrifugal Pump With an Inducer

Cavitation Performance Improvement of High Specific Speed Mixed-Flow Pump

Effects of Different Turbulence Models on Three-Dimensional Unsteady Cavitating Flows in the Centrifugal Pump and Performance Prediction

Hydraulic Optimization and Loss Analyses of a Low Specific-Speed Centrifugal Pump with Variable-Thickness Blades

Numerical Simulation of Flow in Centrifugal Pump with Complex Impeller

Research on Cavitation Characteristic of Inducer

Numerical Simulation of Inner Flow in Equal-pitch Inducer

Numerical Simulation of Inner Flow Field in Centrifugal Impeller with Long, Middle and Short Blades

Experimental and numerical investigations of cavitation evolution in a high-speed centrifugal pump with inducer

Numerical investigation of flow characteristics in the front and rear chambers of centrifugal pump and pump as turbine

Transient Internal Characteristic Study of a Centrifugal Pump During Startup Process

Visual experiment and numerical simulation of cavitation instability in a high-speed inducer

Investigation of turbulence models for aerodynamic analysis of a high-pressure-ratio centrifugal compressor

Numerical Simulation on the Steady and Unsteady Internal Flows of a Centrifugal Pump

3-D Numerical Study on Incompressible Turbulent Flow Inside the Volute of Centrifugal Pump

Numerical Investigation Of Unsteady Turbulent Flow In A Centrifugal Pump At Partial Load

Numerical Analysis of Unstable Turbulent Flows in a Centrifugal Pump Impeller Considering the Curvature and Rotation Effect

Cavitating Flow Investigation Inside Centrifugal Impellers For A Condensate Pump

Research on Visualization of Inducer Cavitation of High-Speed Centrifugal Pump in Low Flow Conditions

Investigation on Cavitation for Hump Characteristics of A Pump Turbine in Pump Mode

Investigation of CFD Calculation Method of a Centrifugal Pump with Unshrouded Impeller