Abstract:A series of composites based on epoxy resin filled with additives of natural origin were prepared to investigate the influence of such fillers on the properties of the epoxy compositions. For this purpose, the composites containing 5 and 10 wt.% of additive of natural origin were obtained using the dispersion of oak wood waste and peanut shells in bisphenol A epoxy resin cured with isophorone-diamine. The oak waste filler had been obtained during the assembly of the raw wooden floor. The performed studies include testing of samples prepared using unmodified and chemically modified additives. Chemical modification via mercerization and silanization was performed to increase the poor compatibility between the highly hydrophilic fillers of natural origin and the hydrophobic polymer matrix. Additionally, the introduction of NH2 groups to the structure of modified filler via 3-aminopropyltriethoxysilane, potentially takes a part in co-crosslinking with the epoxy resin. Fourier Transformed Infrared Spectroscopy (FT-IR), as well as Scanning Electron Microscopy (SEM), were carried out, to study the influence of performed chemical modification on the chemical structure and morphology of wood and peanut shell flour. SEM analyses showed significant changes in the morphology of compositions with chemically modified fillers, indicating improved adhesion of the resin to lignocellulosic waste particles. Moreover, a series of mechanical (hardness, tensile strength, flexural strength, compressive strength, and impact strength) tests were carried out, to assess the influence of the application of fillers of natural origin on the properties of epoxy compositions. All composites with lignocellulosic filler were characterized by higher compressive strength (64.2 MPa-5%U-OF, 66.4%-SilOF, 63.2-5%U-PSF, and 63.8-5%SilPSF, respectively), compared to the values recorded for the reference epoxy composition without lignocellulosic filler (59.0 MPa-REF). The highest compressive strength, among all tested samples, was recorded for the composite filled with 10 wt.% of unmodified oak flour (69.1 MPa-10%U-OF). Additionally, higher values of flexural and impact strength, concerning pure BPA-based epoxy resin, were recorded for the composites with oak filler (respectively, flexural strength: 73.8 MPa-5%U-OF and 71.5 MPa-REF; impact strength: 15.82 kJ/m2-5%U-OF, 9.15 kJ/m2-REF). Epoxy composites with such mechanical properties might be considered as broadly understood construction materials. Moreover, samples containing wood flour as a filler exhibit better mechanical properties compared to those with peanut shell flour (tensile strength for samples containing post-mercerization filler: 48.04 MPa and 40.54 MPa; while post-silanization 53.53 MPa and 42.74 MPa for compositions containing 5 wt.% of wood and peanut shell flour, respectively). At the same time, it was found that increasing the weight share of flour of natural origin in both cases resulted in the deterioration of mechanical properties.

Fracture energy and mechanical properties of toughened epoxy resin with eggshell powder

Tensile, Quasistatic And Dynamic Fracture Properties Of Nano-Al2o3-Modified Epoxy Resin

Effect of silica particle size and filler content on the fracture properties of epoxy resin composite

Investigating the mechanical and insulation performance of waste eggshell powder/epoxy polymer for power insulation application

Silica Nanoparticle-Decorated Alumina Rough Platelets for Effective Reinforcement of Epoxy and Hierarchical Carbon Fiber/epoxy Composites

Preparation of epoxy resin elastic particles and their application in oil well cement

Mechanical Properties and Failure Behavior of Epoxy Rubber Powder Composites Reinforced with Hollow Beads

Effect of eggshell powder on polyvinyl ester composite: A statistical correlation on mechanical strength

Effect of clamshell powder on the mechanical and damping properties of epoxy-bamboo composites

Enhancement of Mechanical Properties and Bonding Properties of Flake-Zinc-Powder-Modified Epoxy Resin Composites

Modification of Epoxy Compositions by the Application of Various Fillers of Natural Origin

The effects of the contents of modified‐diatomite on the properties of modified‐diatomite/epoxy resin composites

Toughening Epoxy Resins by Liquid Crystalline Co-Polyester PET-PHB

A composite nanofiller with a nail column void structure to imitate beetle shell fiber to enhance the impact resistance of polyurethane elastomer

Toughness and its mechanisms in epoxy resins

Enhancing fracture toughness of carbon fiber/epoxy composites using polyphenylene ether as a modifier

Significantly Strengthening Epoxy by Incorporating Carbon Nanotubes/Graphitic Carbon Nitride Hybrid Nanofillers

Investigation of mechanical and morphological traits with the effect of turtle shell powder in kenaf-epoxy composite

Synergistic toughening of epoxy resin by block ionomers and carbon nanofibers

Enhanced mechanical properties of epoxy composites using cellulose micro‐ and nano‐crystals

Mechanical, tribological, and surface morphological studies on the effects of hybrid ilmenite and silicon dioxide fillers on glass fibre reinforced epoxy composites