Abstract:Surface oxidation is known to have a negative impact on the flotation performance of sulphide minerals. This is because severe oxidation makes it more difficult to process low-grade sulphide minerals, which reduces the recovery of valuable minerals during flotation. It may be possible to quantitatively correlate the rate/level of oxidation to oxidized sulphide ores using simple surface analytical techniques. This, if done well, could eliminate the need for numerous mineralogical tests, saving both time and money. This study investigated the EDTA Extraction Technique and Oxygen consumption factor (OCF) Technique as possible techniques to quantitatively describe oxidation levels in different ore types with different mineral compositions and grades. The aim was to determine if the changes in the surface character generated by oxidation are linked to a measurement obtained from the selected techniques. The techniques were validated on fresh ores of varying grades; high grade Cu (HG Cu) and Upper Group 2 (UG2). The two ores were then ground to generate varying particle size distributions and liberation profiles to study the link between oxidation, particle size and liberation. Based on ore type and sulphide liberation, the tests attempted to provide an indicator of feed grade and surface oxidation. Flotation is used as a diagnostic for the parameters mentioned. The results showed that (for Ore A/UG2) as particle size decreased (from grind size 40 %–75 μm), the recovery increased until it hit a maximum (grind size 60 %–75 μm) before monotonically declining (to grind size 80 %–75 μm). The OCF and EDTA values increased as the grind size became finer. The grind size 80 %–75 μm had suffered significantly more oxidation than the other grind sizes and this was indicated by the high OCF and the EDTA value. The liberated base metal sulphides (BMS) for Ore B (HG Cu) was generally consistent throughout the three grind sizes, however, the highest recovery was achieved by the grind size 80 %–75 μm (95.11 %), followed by grind sizes 60 %–75 μm and 40 %–75 μm respectively (92.25 % and 90.86 %). The recovery of this ore increases as the grind size becomes finer. Ore B demonstrated a direct correlation between the OCF and EDTA value for ore B increased as the grind size became finer, and the recovery. It is possible that the particles that were ground to achieve particle size 80 %–75 μm were at their most hydrophobic state, owing to the increased liberation of the BMS, particularly chalcopyrite.

A mineralogy characterisation technique for copper ore in flotation pulp using deep learning machine vision with optical microscopy

Insights Into Ferric Leaching Of Low Grade Metal Sulfide-Containing Ores In An Unsaturated Ore Bed Using X-Ray Computed Tomography

Mineralogical characterization of copper sulfide tailings using automated mineral liberation analysis: A case study of the Chambishi Copper Mine tailings

Study on Flotability and Surface Oxidation of Sulfide Minerals from the Tailing of an Iron-Copper Mine Using Electron Probe Microanalyzer

Iron Oxide-Copper Mineral Associations in Supergene Zones: Insights into Flotation Challenges and Optimization Using Response Surface Methodology

An Innovative Sensor-Based Approach for Evaluating Performance of Flotation Circuit at the Expansion of Toromocho Copper Mine

Novel approach to locate micro-scale mineral regions of interest in real ores

Predictive Geometallurgical Modeling for Flotation Performance in Mixed Copper Ores Using Discriminatory Methods

Machine learning for geochemical exploration: classifying metallogenic fertility in arc magmas and insights into porphyry copper deposit formation

A high throughput screening model of solidophilic flotation reagents for chalcopyrite based on quantum chemistry calculations and machine learning

Assessing Machine learning-based approaches for Silica concentration estimation in Iron Froth flotation

Deep Ensemble Learning-Based Sensor for Flotation Froth Image Recognition

Revealing the Multi-Stage Ore-Forming History of a Mineral Deposit Using Pyrite Geochemistry and Machine Learning-Based Data Interpretation

Machine learning coupled with mineral geochemistry reveals the origin of ore deposits

Ore-Grade Estimation from Hyperspectral Data Using Convolutional Neural Networks: A Case Study at the Olympic Dam Iron Oxide Copper-Gold Deposit, Australia

Data-driven system for intelligent monitoring and optimization of froth flotation circuits using Artificial Neural Networks and Genetic Algorithms

Fusion of Laser-Induced Breakdown Spectroscopy and Raman Spectroscopy for Mineral Identification Based on Machine Learning

Advancements in Machine Learning for Optimal Performance in Flotation Processes: A Review

The use of simple analytical techniques to assess surface oxidation of sulphide ores

A Novel Method for Evaluation of Ore Minerals Based on Optical Microscopy and Image Analysis: Preliminary Results

Research on Beneficiation Technique to Improve Recovery of Deep Mined Copper Ore