Abstract:Surface oxidation is known to have a negative impact on the flotation performance of sulphide minerals. This is because severe oxidation makes it more difficult to process low-grade sulphide minerals, which reduces the recovery of valuable minerals during flotation. It may be possible to quantitatively correlate the rate/level of oxidation to oxidized sulphide ores using simple surface analytical techniques. This, if done well, could eliminate the need for numerous mineralogical tests, saving both time and money. This study investigated the EDTA Extraction Technique and Oxygen consumption factor (OCF) Technique as possible techniques to quantitatively describe oxidation levels in different ore types with different mineral compositions and grades. The aim was to determine if the changes in the surface character generated by oxidation are linked to a measurement obtained from the selected techniques. The techniques were validated on fresh ores of varying grades; high grade Cu (HG Cu) and Upper Group 2 (UG2). The two ores were then ground to generate varying particle size distributions and liberation profiles to study the link between oxidation, particle size and liberation. Based on ore type and sulphide liberation, the tests attempted to provide an indicator of feed grade and surface oxidation. Flotation is used as a diagnostic for the parameters mentioned. The results showed that (for Ore A/UG2) as particle size decreased (from grind size 40 %–75 μm), the recovery increased until it hit a maximum (grind size 60 %–75 μm) before monotonically declining (to grind size 80 %–75 μm). The OCF and EDTA values increased as the grind size became finer. The grind size 80 %–75 μm had suffered significantly more oxidation than the other grind sizes and this was indicated by the high OCF and the EDTA value. The liberated base metal sulphides (BMS) for Ore B (HG Cu) was generally consistent throughout the three grind sizes, however, the highest recovery was achieved by the grind size 80 %–75 μm (95.11 %), followed by grind sizes 60 %–75 μm and 40 %–75 μm respectively (92.25 % and 90.86 %). The recovery of this ore increases as the grind size becomes finer. Ore B demonstrated a direct correlation between the OCF and EDTA value for ore B increased as the grind size became finer, and the recovery. It is possible that the particles that were ground to achieve particle size 80 %–75 μm were at their most hydrophobic state, owing to the increased liberation of the BMS, particularly chalcopyrite.

Study on Flotability and Surface Oxidation of Sulfide Minerals from the Tailing of an Iron-Copper Mine Using Electron Probe Microanalyzer

Mineralogical characterization of copper sulfide tailings using automated mineral liberation analysis: A case study of the Chambishi Copper Mine tailings

Experimental Study on Activated Sulfur Selection from High Alkalinity Lead Zinc Flotation Tailings

Study on Recovery of Lead-Zinc Tailing Ore by Electrochemical Flotation

Flotation separation of chalcopyrite and pyrite via Fenton oxidation modification in a low alkaline acid mine drainage (AMD) system

Experimental Study on Comprehensive Recovery of Valuable Minerals from Flotation Tailings in Copper-Molybdenum Mine

An Electrochemical Study of Surface Oxidation and Collectorless Flotation of Pyrite

Characterization of Discarded Lead–Zinc Sulfide Ore Tailings Based on Mineral Fragments

Research on Bulk Floatation Discarding Tailing of Copper and Zinc Polymetallic Sulfide Ores

Experiment Study on New Processing of a Mixed Flotation of Recoverying Complex Copper-Lead-Zinc Polymetallic Sulphide Ore

The critical degree of mineral surface oxidation in copper sulphide flotation

Exploiting the Influence of Oxidization on Ultra-Fine Copper and Nickel Sulfide Containing Pt-Pd in Yunnan Mine

Studies on the surface oxidation and its role in the flotation of mixed Cu-Ni sulfide ore

Probe into hydrophobic mechanism of solid-liquid interface during separation recovery of Zn from Fe and Cd by sulfide precipitation flotation with a novel “plane” collector

Study on Flotation of a Refractory Copper-zinc Polymetallic Sulfide Ore

The use of simple analytical techniques to assess surface oxidation of sulphide ores

An experimental comparison: Horizontal evaluation of valuable metal extraction and arsenic emission characteristics of tailings from different copper smelting slag recovery processes.

Surface Analytical Studies of Oxidation and Collector Adsorption in Sulfide Mineral Flotation

Spectroelectrochemistry study on the surface modification of chalcopyrite by Cu 2+ and its depressive response to flotation collector adsorption by negative potential

The Influence of Sulphide Tailing Water on the Flotation Performance of Pyrite