Abstract:When a single-phase-to-ground (SPG) fault occurs in a distribution network, the current is weak, and the fault conditions are complex; the existing fault detection technologies do not show reliable performance. Unlike the existing detection methods, we introduced a fundamental component shift and multiple-transient-feature fusion method in this article. To remove the fundamental component (FC) that contained in the transient zero-sequence current (TZSC), Hilbert transform was used to calculate the analytic signal of TZSC. Then, the shift factor was introduced to remove the FC such that all the transient features can be kept. Second, three typical transient features indexes were calculated. Then, the multiple evidence estimation method was used to fuse the transient features indexes. Finally, selected the feeder with the maximum fault degree as the faulty feeder. To verify the accuracy and extensive applicability of the proposed method, developed the sample radial distribution network model with different fault conditions, arc fault model, and the modified IEEE-34-node test system with power electronics generator and wind energy conversion systems, the proposed method shows good performance.

What problem does this paper attempt to address?

The paper attempts to address the issue of reliability in single-phase ground (SPG) fault detection in distribution networks. Specifically: 1. **Background and Challenges**: - Single-phase ground faults account for more than 80% of all fault types and need to be detected promptly to isolate the fault section. - With the integration of renewable energy systems such as wind and solar power, detecting SPG faults becomes particularly important to ensure power quality and protect power electronic devices. - Existing protection devices cannot accurately detect SPG faults due to the small amplitude of transient zero-sequence current (TZSC). 2. **Limitations of Existing Methods**: - **Steady-state methods**: Performance is unstable due to the influence of grid operating modes and grounding resistance. - **Transient methods**: Although modern signal processing algorithms are used to extract rich transient fault features and improve detection accuracy, these methods have some limitations, such as wavelet transform (WT) being sensitive to the choice of mother wavelet function, and Hilbert-Huang transform (HHT) having issues like mode mixing and endpoint effects. 3. **Proposed Method in the Paper**: - Introduced a fundamental component shifting and multi-transient feature fusion method. - Used Hilbert transform to calculate the analytic signal of TZSC, introduced a shifting factor to remove the fundamental component (FC), and retained all transient features. - Calculated three typical transient feature indicators: transient energy (TE), kurtosis value, and cross-correlation distance (CCD). - Used a multi-evidence estimation method to fuse transient feature indicators and selected the feeder with the highest fault degree as the fault feeder. 4. **Validation and Application**: - The proposed method's accuracy and broad applicability were validated by developing a sample radial distribution network model, an arc fault model under different fault conditions, and a modified IEEE-34 node test system (including power electronic generators and wind energy conversion systems). In summary, the paper aims to improve the reliability and accuracy of single-phase ground fault detection in distribution networks by introducing new signal processing methods and feature fusion techniques to overcome the limitations of existing methods.

Faulty Feeder Detection Based on Fundamental Component Shift and Multiple-Transient-Feature Fusion in Distribution Networks

Single-phase-to-ground Fault Detection with Distributed Parameters Analysis in Non-Direct Grounded Systems

Faulty Feeder Detection for Single-Phase-to-Ground Fault in Distribution Networks Based on Transient Energy and Cosine Similarity

Faulty feeder detection based on the fluctuation characteristics of inflection point dense area for DC distribution network

Study on fault line detection methods based on multi‐feature fusion in distribution systems

Faulty feeder detection of single phase-earth fault based on fuzzy measure fusion criterion for distribution networks

Faulty feeder detection of single phase-to-ground fault for distribution networks based on improved K-means power angle clustering analysis

Faulty Feeder Identification Based on Data Analysis and Similarity Comparison for Flexible Grounding System in Electric Distribution Networks

Faulty Feeder Detection Under High Impedance Faults for Resonant Grounding Distribution Systems

Faulty Feeder Detection Method Based on VMD–FFT and Pearson Correlation Coefficient of Non-Power Frequency Component in Resonant Grounded Systems

Faulty Feeders Identification for Single-phase-to-ground Fault Based on Multi-features and Machine Learning

Faulty feeder selection based on improved Hough transform in resonant grounded distribution networks

Faulty Feeder Detection Based on Space Relative Distance for Compensated Distribution Network With IIDG Injections

Faulted Feeder Identification Based on Active Adjustment of Arc Suppression Coil and Similarity Measure of Zero-Sequence Currents

A visual faulty feeder detection method for power distribution network based on spatial image generation and deep learning

Faulty Feeder Selection and Segment Location Method for SPTG Fault in Radial MMC-MVDC Distribution Grid

Fault Sections Detection and Isolation in Distribution System Based on FTU

Faulted Feeder Selection in Neutral Non-Effectively Grounded Distribution System Using Single-Phase Current Traveling Wave

High Impedance Fault Detection in Overhead Distribution Feeders Using a DSP-Based Feeder Terminal Unit

Incipient Fault Detection and Condition Assessment in DFIGs Based on External Leakage Flux Sensing and Modified Multiscale Poincare Plots Analysis

High-impedance Fault Detection Method Based on Feature Extraction and Synchronous Data Divergence Discrimination in Distribution Networks