Abstract:Redox flow batteries based on sodium polysulfide (Na 2 Sx) show promise due to sodium's high solubility in organic solvents (e.g., diglyme. However, when x is lower than 5, sodium polysulfide exhibits low solubility (less than 0.1 molal), limiting the nominal capacity of this redox-active material. Sodium phosphorothioate complexes, Na 2 P 2 Sx, have been reported as an alternative to Na2Sx. Incorporating phosphorus into the polysulfide structure improves their solubility in organic solvents, specifically in diglyme. This presentation will describe the synthesis and characterization of sodium phosphorothioate complexes (Na 2 P 2 S x , where x = 6, 7, 8, and 9) for nonaqueous redox flow batteries. The structure of these materials is explored using 31 P NMR and 23 Na NMR spectroscopy, Raman spectroscopy, and X-ray diffraction analysis. Overall, 31 P NMR results indicate that P 5+ is tetrahedrally coordinated in all structures and that Na-P-S compounds have a common PS 3 - moiety. Ongoing efforts are aimed at providing more precise assignments to the 31 P bands and correlating these findings with complementary structural information obtained from 23 Na NMR and Raman spectroscopy. Electrochemical properties of sodium polysulfide and sodium thiophosphate catholytes, specifically Na 2 S 8 and Na 2 P 2 S 8 , were also compared using CV. The voltammogram of Na 2 S 8 revealed two clear redox reactions in the 1.5-3 V range vs. Na/Na + due to a multi-step electron transfer process involving the S 2- /S 0 redox center. In contrast, Na 2 P 2 S 8 exhibited a larger peak separation (~2 V) and lower peak currents at a given scan rate, potentially indicating a significant activation barrier associated with the rearrangement of the thiophosphate’s polyanionic structure during reduction/oxidation. Despite the substantial voltage hysteresis, Na 2 P 2 S 8 displayed stable cycling performance, with a slight increase in peak current after 100 cycles. This behavior is consistent with measurements on RFBs containing a Na 2 P 2 S x catholyte, where an electrode activation process increased the cell’s reversible capacity, likely due to subtle changes in the electrode’s surface chemistry during repeated oxidation/reduction. Finally, preliminary flow cell measurements on Na 2 P 2 S 7 catholyte show reversible voltage profiles after the formation step with deep discharge. Overall, this presentation demonstrates that Na-P-S catholytes represent a promising material for high energy, low-cost redox flow batteries. Acknowledgements This research was conducted at Oak Ridge National Laboratory, managed by UT Battelle, LLC, for the U.S. Department of Energy (DOE) and is sponsored by the U.S. Department of Energy through the Energy Storage Program in the Office of Electricity.

Improved Formulation and Optimization of Sodium Polysulfide/Bromine Electrolytes for Redox Flow Battery

Sodium Metal Hybrid Redox Flow Batteries Containing Sulfide and Thiophosphate Catholytes

Sodium Polysulfides As Catholytes for Redox Flow Batteries

Research Progress in Sodium Polysulfide/bromine Redox Flow Battery

Lewis Acid–Base Interactions between Polysulfides and Boehmite Enables Stable Room‐Temperature Sodium–Sulfur Batteries

Electrolytes with Controlled Polysulfide Insolvability for Lithium-Sulfur Batteries

Rational Electrolyte Design Toward Cyclability Remedy for Room‐Temperature Sodium–Sulfur Batteries

A Stable and Energy-Dense Polysulfide/Permanganate Flow Battery

Electrochemical Stability and Reversibility of Aqueous Polysulfide Electrodes Cycled Beyond the Solubility Limit

Successive ionic layer adsorption and reaction–deposited copper sulfide electrocatalyst for high-power polysulfide-based aqueous flow batteries

Electrolyte optimization for sodium-sulfur batteries

Entrapment of Polysulfides by Al2O3 Modified Separator for High Energy Li–S Redox Flow Batteries

Aqueous Polysulfide-Based Redox Flow Battery with Soluble Molecular Catalysts

High-Capacity CuSi2P3-Based Semisolid Anolyte for Redox Flow Batteries.

Sandwiched Cu7S4@graphite Felt Electrode for High Performance Aqueous Polysulfide/iodide Redox Flow Batteries: Enhanced Cycling Stability and Electrocatalytic Dynamics of Polysulfides

Thiosulfate‐Mediated Polysulfide Redox for Energetic Aqueous Battery

Nickel Foam and Carbon Felt Applications for Sodium Polysulfide/bromine Redox Flow Battery Electrodes

Redox-Active Eutectic Electrolyte with Viologen and Ferrocene Derivatives for Flow Batteries

Mechanistic Understanding of a Bifunctional Electrolyte Additive as a Solvation-Property Modifier and Polysulfide Mediator for Enhanced Performance in Lithium-Sulfur Battery

Electrolytes with Solvating Inner Sheath Engineering for Practical Na-S Batteries

Strategic Electrolyte Design to Address Solubility Competition between Redox-Active Molecules and Supporting Salts