Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Determination of overall factor for the application of the General Method based on plastic and strain‐limited N‐M interaction for composite compression members

Evaluation of Simplified Superposition Design Method for Composite Columns

Experimental and Numerical Study of 7A04-T6 Extruded Aluminium Alloy Lipped Angle Columns in Axial Compression

General method for I‐section stainless steel beam‐columns

Experimental Investigation and Design of Hollow Section, Centrifugal Concrete-Filled GFRP Tube Columns

Numerical Investigation on Compressive Performance of CFST Columns with Encased Built-Up Lattice-Angles

Compressive Behavior and Design Calculations of CFST Slender Columns with Latticed Annular Steel Part

Enhanced buckling reduction factors using amplified imperfections for existing steel structures

Equivalent geometric imperfections for the design of steel and stainless steel beam-columns by GMNIA

An assessment of application of the component-based method to full range behaviour of joints between steel beam to concrete filled steel tube columns under extreme loading conditions

Influence of load arrangement on composite slab behaviour and recommendations for design

Determination of the bearing capacity of encentrally compressed concrete filled steel tubular columns on the basis of the deformation theory of concrete plasticity

Eurocode-compliant system-level reliability analyses of trussed portal frames under climatic loads

Global Safety Factor or Nonlinear Design of Concrete Structures

Experimental study on the performance of special-shaped columns composited with HGM-filled square steel tube under axial compression

On the Verification of Beams Subjected to Lateral Torsional Buckling by Simplified Plastic Structural Analysis

Numerical Procedure for the Three-Dimensional Nonlinear Modelling of Composite Steel–Concrete Beams

Strain-based method for assessment of global resistance safety factors for NLNAs of reinforced concrete structures

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns

Prediction of Lateral Deflection and Moment of Partially-Encased Composite Beam-Columns

CALCULATION METHOD FOR DETERMINATION OF ADHESION LEVEL OF COMPOSITE REINFORCEMENT WITH CONCRETE