Abstract:The paper investigates the characteristics of the laser beam percussion micro-drilling (LBPMD) process in aerospace nickel-based superalloy Hastelloy X using microsecond pulses. The quality of the drilled hole is crucial in laser beam micromachining, and selecting appropriate process parameters significantly impacts the hole's quality. The objective is to achieve predefined hole dimensions with minimal taper angles. Additionally, the study focuses on the alteration of pulse width, which is a combination of laser pulse frequency and duty cycle. Laser power ( P ), duty cycle % ( D ), focal plane position ( FPP ), and laser frequency ( f ) are considered input parameters, while geometric features such as inlet and outlet diameters, hole taper angle, and inlet circularity are examined as process responses. ANOVA is employed to establish significant relationships between process parameters and response variations based on experimental tests. Creating a precise simulation model that accurately accounts for the moving boundary of the target material's receding surface is a crucial and challenging task in formulating the laser heat conduction problem. It is necessary to simultaneously capture the material's dynamic front movement and update the boundary conditions of the laser source. To model the micro-drilled hole with LBPMD, the UMESHMOTION and DFLUX subroutines, along with the arbitrary Lagrangian-Eulerian (ALE) adaptive remesh algorithm in the AbaqusTM software, are utilized. Notably, no previous numerical study has predicted the geometry of micro-drilled holes using this technique. The proposed procedure is validated through the predictions of inlet and outlet hole diameters. Special emphasis is placed on the validation of models. Consequently, the numerical model and statistical model are compared as well as the need to define model applicability. The study demonstrates that all input parameters significantly influence the inlet hole diameter, while the pulse width notably affects the taper angle and circularity. The interaction between high laser frequency and low duty cycle results in reduced pulse duration. Multi-objective optimization is performed to determine the optimal process parameter settings for desired quality characteristics, considering minimum hole taper angle, precise inlet diameter, and maximum inlet circularity of the hole as optimization criteria. The findings show that with the optimized predicted results obtained from the optimal input variables, a composite desirability of 92% can be achieved.

Experimental characterization of the inner surface in micro-drilling of spray holes: A comparison between ultrashort pulsed laser and EDM

Study of High-Speed Microhole Drilling by Combined Process using Laser and EDM-Apply for fuel injection nozzle-

High Speed EDM and Laser Drilling of Aerospace Alloys

Study of the Law Motion of the Micro-EDM Drilling Process

Performance analysis of powder-assisted micro-drilling operation using micro-EDM

Mass Fabrication of Microholes in Aviation Kerosene Filters Using the Back-water-assisted Picosecond Laser Drilling Technique

An investigation on the effect of alumina nano powder mixed dielectric oil on EDM-assisted precision micro-drilling operation

A novel numerical modeling of microsecond laser beam percussion micro-drilling of Hastelloy X: experimental validation and multi-objective optimization

A review on short and ultrashort pulsed laser microdrilling: materials, mechanism, methods, and applications

Experimental investigation and optimization of modification during coaxial waterjet-assisted femtosecond laser drilling

A comprehensive study on water jet guided laser micro hole drilling of an aerospace alloy

Mechanism design and process control of micro EDM for drilling spray holes of diesel injector nozzles

Micro Electrochemical Machining for Tapered Holes of Fuel Jet Nozzles

Comparative investigations on machinability and surface integrity of CFRP plate by picosecond laser vs laser induced plasma micro-drilling

Effect of laser parameters on sequential laser beam micromachining and micro electro-discharge machining

Experimental research on micro-drilling of refractory material tungsten by multi-pulse femtosecond laser ablation

Research on Drilling Taper Holes of Fuel Jet Nozzles by Micro EDM

Micro Drilling of PMMA with Double-Pulse Femtosecond Laser

Numerical and experimental investigations to analyze the micro-hole drilling process in spark-assisted chemical engraving (SACE)

A Deep-Hole Microdrilling Study of Pure Magnesium for Biomedical Applications

A Cutting Force and Hole Geometry Study for Precision Deep-Hole Microdrilling of Magnesium