Abstract:Micro-EDM is an unconventional technology used to machine every type of electrically conductive material regardless of its mechanical properties. Material removal occurs through electrical discharges between the workpiece and the electrode immersed in a dielectric fluid. In drilling operations, the technology is able to realise microholes with excellent quality in terms of precision, quality surface, roundness, and taper to the detriment of the machining time, which is less than other technologies. Several efforts are being made to improve different features related to the process performance that are severely affected by both the operative conditions, such as the electrode material or the type of dielectric, and process parameters. The typical indexes used to characterise the performance are the machining time, the material removal rate, and the geometric indexes. These indexes are very effective and are easily measurable, but they do not give information about the evolution of the drilling process, which could be irregular due to the different phenomena occurring during machining. The aim of this paper is the development of a method able to elaborate the motion law of the electrode during the micro-EDM drilling operation. In order to do this, a single hole was manufactured in several steps, recording both the machining time and electrode wear for each step. In this way, the actual position of the electrode during the drilling can be measured without the use of a predictive model for electrode wear. It was tested to confirm that the multistep procedure did not introduce new phenomena, in contrast to the traditional drilling operation. This method was used to study the effects of the electrode diameter, the type of electrode, the length of the electrode out of the spindle, and the entity of the run-out on the process performance. The tests were executed on titanium alloy sheets using a tungsten carbide electrode and hydrocarbon oil as the dielectric. It was found that the descent of the electrode into the workpiece was not regular, but it depended on the level of debris concentration in the machining zone. The debris concentration was influenced by the type and diameter of the electrode, its length out of the spindle, and, to a lesser extent, the run-out. This method was found to be a useful method for an in-depth analysis of the micro-EDM drilling process, contributing to a better understanding of the physical aspects of the process.

Study of High-Speed Microhole Drilling by Combined Process using Laser and EDM-Apply for fuel injection nozzle-

Mechanism design and process control of micro EDM for drilling spray holes of diesel injector nozzles

High Speed EDM and Laser Drilling of Aerospace Alloys

Micro Electrochemical Machining for Tapered Holes of Fuel Jet Nozzles

Research on Drilling Taper Holes of Fuel Jet Nozzles by Micro EDM

EDM Drilling Process of Micro Tapered Holes by Online Control of Machining Parameters

Design of Electromechanical Control System of EDM for Drilling Micro Nozzles

An investigation on the effect of alumina nano powder mixed dielectric oil on EDM-assisted precision micro-drilling operation

Experimental characterization of the inner surface in micro-drilling of spray holes: A comparison between ultrashort pulsed laser and EDM

Mass Fabrication of Microholes in Aviation Kerosene Filters Using the Back-water-assisted Picosecond Laser Drilling Technique

Performance analysis of powder-assisted micro-drilling operation using micro-EDM

A novel EDM method using longitudinal-torsional ultrasonic vibration (LTV) electrodes to improve machining performance for micro-holes

Performance improvement of high-speed EDM and ECM combined process by using a helical tube electrode with matched internal and external flushing

Experimental study of EDM milling of 3D-shaped diffuser for film cooling holes on turbine blades

Improvement of ultrasonic cavitation and pumping effect in microhole EDM

Study of the Law Motion of the Micro-EDM Drilling Process

A High Energy Density Pulsed Power Supply for Micro EDM of High Aspect Ratio Holes

A Hybrid Machining Process Combining Micro-EDM and Laser Beam Machining of Nickel–Titanium-Based Shape Memory Alloy

To investigate the effect of discharge energy and addition of nano-powder on processing of micro slots using EDM assisted μ-milling operation

A Method of Hole Pass-Through Evaluation for EDM Drilling

Precision EDM of Micron-Scale Diameter Hole Array Using in-Process Wire Electro-Discharge Grinding High-Aspect-Ratio Microelectrodes