Abstract:Supercritical CO2 (S-CO2) leakage through seals significantly reduces the efficiency of turbomachinery. Improving the labyrinth seal structure is potentially the key to the reduction of the leakage flow rate, but its application is greatly limited by the uncertainties of supercritical CO2 turbulent flow inside the turbomachines with irregular chambers. In this work, we numerically investigated the S-CO2 flow field and dissipation rate of turbulence kinetic energy in stepped labyrinth seals. The RANS method and hexahedral structural mesh were employed. The look-up table containing the real gas properties of carbon dioxide was created and imported into the flow solver. The developed numerical method was validated by experiment results and proved its applicability. We have discovered that the fully developed rotating vortices inside each chamber of the turbomachine significantly increase the turbulent dissipation rate and decrease the fluid carried energy, thus reducing the leakage flow rate. With the seal clearance increasing form 0.5 mm-1.3 mm at pressure ratio pi = 0.7, the vortices development is gradually limited, causing the decrease of turbulent dissipation rate. The leakage rate is found to be heavily dependent on the distance between the seal tip and step. The increase in this distance from 2 mm to 6 mm results in greater space for the continued development of the vortices within the first chamber, thus the enhancement of the turbulent dissipation rate of fluid. Therefore, we defined a geometry coefficient, (delta-b)/s, and analyzed its effects on turbulent dissipation rate and leakage flow rate. With this geometry coefficient increases from 2.8 to 11.2 at pi = 0.7, the maximum turbulent dissipation rate increases from 7.09 x 107 to 1.23 x 108 and the leakage flow rate decreases from 3.98 x 10-2 kg/s to 1.62 x 10-2 kg/s. An improved leakage model characterizing seal geometry, gas properties and compressibility effects was proposed.

Numerical Simulation of Supercritical Carbon Dioxide Dry Gas Seal

Effect of T-groove Parameters on Steady-State Characteristics of Cylindrical Gas Seal

Research on the Performance of Supercritical CO2 Dry Gas Seal with Different Deep Spiral Groove

Calculation and verification of flow field in supercritical carbon dioxide dry gas seal based on turbulent adiabatic flow model

Static and Rotordynamic Characteristics for Supercritical Carbon Dioxide Spiral Groove Dry Gas Seal with the Tilted Seal Ring

Numerical study on sealing performance of supercritical carbon dioxide compressor dry gas seal

High-Temperature Flow Behavior and Energy Consumption of Supercritical CO2 Sealing Film Influenced by Different Surface Grooves

Experimental and Numerical Investigation on the Dynamic Characteristics of a Lab-Scale Transcritical CO2 Loop

Thermo-hydrodynamic analysis of spiral groove dry gas seals

Design and Investigations on Dry Gas Seal of the Shaft End for 450mwe Supercritical Carbon Dioxide Compressor

Dynamic Characteristics of Supercritical Carbon Dioxide (SCO2) Seal Influenced by Multiple Factors

Flow Numerical Simulation of Dry Gas Seal with Double-row Spiral Grooves

Effects of Surface Micro-Scale and Thermal Viscosity on Sealing Performance of Spiral-Grooved Dry Gas Seal

Turbulence Dissipation of Leakage Flow in Supercritical CO2 Labyrinth Seals

Thermal characteristics and cooling effect for SCO2 dry gas seal with multiple dynamic groove types

Numerical Investigation on Hydrodynamic Characteristics of Supercritical CO2 Cylindrical Film Seal

Numerical Study on Rotor Cooling of Turbine in Supercritical Carbon Dioxide Cycle

Numerical Investigation on Flow Characteristics and Aerodynamic Performance of Shroud Seal in a Supercritical CO2 Axial-Flow Turbine

Thermoelastohydrodynamic Behavior of Gas Spiral Groove Face Seals Operating at High Pressure and Speed

Numerical Investigation for Windage Loss and Flow Characteristics Analysis with Supercritical CO2 in Labyrinth Seal

Lubrication Characteristics of Dry-Gas Seals with Spiral Grooves